A stretch/bend method for the in situ measurement of the delamination toughness of coatings attached to substrates is described. A beam theory analysis is presented that illustrates the main features of the test. The analysis is general and allows for the presence of residual stress. It reveals that the test produces stable extension of delaminations, rendering it suitable for multiple measurements in a single test. It also provides scaling relations and enables estimates of the loads needed to extend delaminations. Finite element calculations reveal that the beam theory solutions are accurate for slender beams, but overestimate the energy release rate for stubbier configurations and short delaminations. The substantial influence of residual stress on the energy release rate and phase angle is highly dependent on parameters such as the thickness and modulus ratio for the two layers. Its effect must be included to obtain viable measurements of toughness. In a companion paper, the method has been applied to a columnar thermal barrier coating deposited onto a Ni-based super-alloy.
Skip Nav Destination
Article navigation
January 2011
Research Papers
A Stretch/Bend Method for In Situ Measurement of the Delamination Toughness of Coatings and Films Attached to Substrates
M. Y. He,
M. Y. He
Department of Materials,
University of California, Santa Barbara
, Santa Barbara, CA 93106-5050
Search for other works by this author on:
J. W. Hutchinson,
J. W. Hutchinson
School of Engineering and Applied Sciences,
Harvard University
, Cambridge, MA 02138
Search for other works by this author on:
A. G. Evans
A. G. Evans
Department of Materials,
University of California, Santa Barbara
, Santa Barbara, CA 93106-5050
Search for other works by this author on:
M. Y. He
Department of Materials,
University of California, Santa Barbara
, Santa Barbara, CA 93106-5050
J. W. Hutchinson
School of Engineering and Applied Sciences,
Harvard University
, Cambridge, MA 02138
A. G. Evans
Department of Materials,
University of California, Santa Barbara
, Santa Barbara, CA 93106-5050J. Appl. Mech. Jan 2011, 78(1): 011009 (5 pages)
Published Online: October 13, 2010
Article history
Received:
February 22, 2010
Posted:
June 9, 2010
Revised:
June 25, 2010
Published:
October 13, 2010
Online:
October 13, 2010
Citation
He, M. Y., Hutchinson, J. W., and Evans, A. G. (October 13, 2010). "A Stretch/Bend Method for In Situ Measurement of the Delamination Toughness of Coatings and Films Attached to Substrates." ASME. J. Appl. Mech. January 2011; 78(1): 011009. https://doi.org/10.1115/1.4001938
Download citation file:
Get Email Alerts
Cited By
Sound Mitigation by Metamaterials With Low-Transmission Flat Band
J. Appl. Mech (January 2025)
Deformation-Dependent Effective Vascular Permeability of a Biological Tissue Containing Parallel Microvessels
J. Appl. Mech (January 2025)
Mechanics of a Tunable Bistable Metamaterial With Shape Memory Polymer
J. Appl. Mech (January 2025)
Related Articles
Analysis and Testing of Mixed-Mode Interlaminar Fracture Behavior of Glass-Cloth∕Epoxy Laminates at Cryogenic Temperatures
J. Eng. Mater. Technol (October,2005)
Delamination Cracking in Thermal Barrier Coating System
J. Eng. Gas Turbines Power (October,2002)
Delamination Risk Evaluation for Plastic Packages Based on Mixed Mode Fracture Mechanics Approaches
J. Electron. Packag (December,2002)
Related Chapters
Comparison of Delamination Characterization for IM7/8552 Composite Woven and Tape Laminates
Composite Materials: Testing and Design, Fourteenth Volume
STRUCTURAL RELIABILITY ASSESSMENT OF PIPELINE GIRTH WELDS USING GAUSSIAN PROCESS REGRESSION
Pipeline Integrity Management Under Geohazard Conditions (PIMG)
Combined Effect of Matrix Cracking and Free Edge on Delamination
Composite Materials: Fatigue and Fracture (Third Volume)