Recent results demonstrate the exquisite sensitivity of cell orientation responses to the pattern of imposed deformation. Cells undergoing pure in-plane uniaxial stretching orient differently than cells that are simply elongated—likely because the latter stimulus produces simultaneous compression in the unstretched direction. It is not known, however, if cells respond differently to pure stretching than to pure compression. This study was performed to address this issue. Human aortic endothelial cells were seeded on deformable silicone membranes and subjected to various magnitudes and rates of pure stretching or compression. The cell orientation and cytoskeletal stress fiber organization responses were examined. Both stretching and compression resulted in magnitude-dependent but not rate-dependent orientation responses away from the deforming direction. Compression produced a slower temporal response than stretching. However, stress fiber reorganization responses–early disruption followed by reassembly into parallel arrays along the cells’ long axes were similar between the two stimuli. Moreover, the cell orientation and stress fiber responses appeared to be uncoupled since disruption of stress fibers was not required for the cell orientation. Moreover, parallel actin stress fibers were observed at oblique angles to the deforming direction indicating that stress fibers can reassemble when undergoing deformation.
Skip Nav Destination
Article navigation
October 2004
Technical Papers
Comparison of the Effects of Cyclic Stretching and Compression on Endothelial Cell Morphological Responses
Jeremiah J. Wille,
Jeremiah J. Wille
Department of Biomedical Engineering, P.O. Box 1097, One Brookings Drive, Washington University in St. Louis, St. Louis, Missouri USA
**
Search for other works by this author on:
Christina M. Ambrosi,
Christina M. Ambrosi
Department of Biomedical Engineering, P.O. Box 1097, One Brookings Drive, Washington University in St. Louis, St. Louis, Missouri USA
Search for other works by this author on:
Frank C-P Yin
Frank C-P Yin
Department of Biomedical Engineering, and Department of Medicine, P.O. Box 1097, One Brookings Drive, Washington University in St. Louis, St. Louis, Missouri USA
Search for other works by this author on:
Jeremiah J. Wille
**
Department of Biomedical Engineering, P.O. Box 1097, One Brookings Drive, Washington University in St. Louis, St. Louis, Missouri USA
Christina M. Ambrosi
Department of Biomedical Engineering, P.O. Box 1097, One Brookings Drive, Washington University in St. Louis, St. Louis, Missouri USA
Frank C-P Yin
Department of Biomedical Engineering, and Department of Medicine, P.O. Box 1097, One Brookings Drive, Washington University in St. Louis, St. Louis, Missouri USA
Contributed by the Bioengineering Division for publication in the JOURNAL OF BIOMECHANICAL ENGINEERING. Manuscript received by the Bioengineering Division June 13, 2003; revision received February 20, 2004. Associate Editor: C. Dong.
J Biomech Eng. Oct 2004, 126(5): 545-551 (7 pages)
Published Online: November 23, 2004
Article history
Received:
June 13, 2003
Revised:
February 20, 2004
Online:
November 23, 2004
Citation
Wille, J. J., Ambrosi, C. M., and Yin, F. C. (November 23, 2004). "Comparison of the Effects of Cyclic Stretching and Compression on Endothelial Cell Morphological Responses ." ASME. J Biomech Eng. October 2004; 126(5): 545–551. https://doi.org/10.1115/1.1798053
Download citation file:
Get Email Alerts
Simultaneous Prediction of Multiple Unmeasured Muscle Activations Through Synergy Extrapolation
J Biomech Eng (March 2025)
Related Articles
Esophageal Prosthesis For Refractory Gastresophageal Reflux Disease Prevention
J. Med. Devices (June,2011)
Design of an Endoreactor for the Cultivation of a Joint-Like-Structure
J. Med. Devices (June,2009)
On the Determination of the Angular Orientation of a Vertebra
J Biomech Eng (February,2002)
Response to Dr. Robert W. Mann
J Biomech Eng (August,2004)
Related Proceedings Papers
Related Chapters
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
Analysis of Components: Strain- and Deformation-Controlled Limits
Design & Analysis of ASME Boiler and Pressure Vessel Components in the Creep Range
Analysis of Components Strain and Deformation-Controlled Limits
Analysis of ASME Boiler, Pressure Vessel, and Nuclear Components in the Creep Range