In this paper, the effects of gas flow rates and catalyst loading on polymer electrolyte membrane fuel cell (PEMFC) performance was investigated using a 50 cm2active area fuel cell fixture with serpentine flow field channels machined into poco graphite blocks. Membrane electrode assemblies (MEAs) with catalyst and gas flow rates at two levels each (0.5 mg/cm2, 1 mg/cm2; 0.3 l/min, 0.5 l/min, respectively) were tested at 60 °C without humidification. The cell performance was analyzed by taking ac impedance, Tafel plot, open circuit voltage, and area specific resistance measurements. It was observed that MEAs with lower gas flow rate had lesser cell resistance compared to MEAs with a higher gas flow rate. Tafel plot shows the highest exchange current density value of 10−2.05 mA cm2 for MEA with 0.5 mg/cm2 catalyst loading tested at reactant gas flow rate of 0.3 l/min signifying it had the least activation loss and fastest reaction rate. Open circuit voltage-time curve shows a higher output voltage and lesser voltage decay rate for MEAs tested at higher gas flow rates.
Skip Nav Destination
e-mail: hcmvk3@mst.edu
Article navigation
February 2012
This article was originally published in
Journal of Fuel Cell Science and Technology
Research Papers
Investigation of the Effects of Catalyst Loading and Gas Flow Rate on Polymer Electrolyte Membrane (PEM) Fuel Cell Performance and Degradation
Hector-Martins C. Mogbo
Hector-Martins C. Mogbo
Department of Mechanical and Aerospace Engineering,
e-mail: hcmvk3@mst.edu
Missouri University of Science and Technology, Rolla
, MO
65409-0050
Search for other works by this author on:
Anthony C. Okafor
Mem. ASME e-mail:
Hector-Martins C. Mogbo
Department of Mechanical and Aerospace Engineering,
Missouri University of Science and Technology, Rolla
, MO
65409-0050e-mail: hcmvk3@mst.edu
J. Fuel Cell Sci. Technol. Feb 2012, 9(1): 011006 (13 pages)
Published Online: December 19, 2011
Article history
Received:
May 18, 2010
Revised:
September 16, 2011
Online:
December 19, 2011
Published:
December 19, 2011
Citation
Okafor, A. C., and Mogbo, H. C. (December 19, 2011). "Investigation of the Effects of Catalyst Loading and Gas Flow Rate on Polymer Electrolyte Membrane (PEM) Fuel Cell Performance and Degradation." ASME. J. Fuel Cell Sci. Technol. February 2012; 9(1): 011006. https://doi.org/10.1115/1.4005120
Download citation file:
Get Email Alerts
Cited By
State of health estimation method for Lithium-ion batteries based on multi-feature fusion and BO-BiGRU model
J. Electrochem. En. Conv. Stor
A Fault Diagnosis Method for Electric Vehicle Lithium Power Batteries Based on Dual-Feature Extraction From the Time and Frequency Domains
J. Electrochem. En. Conv. Stor (August 2025)
Optimization of thermal non-uniformity challenges in liquid-cooled lithium-ion battery packs using NSGA-II
J. Electrochem. En. Conv. Stor
Ultrasound-enabled adaptive protocol for fast charging of lithium-ion batteries
J. Electrochem. En. Conv. Stor
Related Articles
Optimizing the Performance of a Single PEM Fuel Cell
J. Fuel Cell Sci. Technol (August,2008)
Multi-Resolution PEM Fuel Cell Model Validation and Accuracy Analysis
J. Fuel Cell Sci. Technol (February,2006)
An Experimental Investigation of the Effects of the Environmental Conditions and the Channel Depth for an Air-Breathing Polymer Electrolyte Membrane Fuel Cell
J. Fuel Cell Sci. Technol (November,2008)
Modeling and Simulation of PEM Fuel Cells With CO Poisoning
J. Energy Resour. Technol (June,2003)
Related Proceedings Papers
Related Chapters
Experiment Study on the Current Density Distribution of PEMFC
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)
Cubic Lattice Structured Multi Agent Based PSO Approach for Optimal Power Flows with Security Constraints
International Conference on Software Technology and Engineering, 3rd (ICSTE 2011)
Elemental Analysis of Process Catalysts
Elemental Analysis of Fossil Fuels and Related Materials