Phase Doppler measurements of size, velocity, liquid flux, and average mass fractions were obtained in sprays produced by three identical coaxial airblast atomizers, with their axes placed in a triangular arrangement at distances of two air jet diameters from each other; the arrangement simulates the spray interaction in the preburner of the space shuttle main engine with water and air respectively replacing the liquid oxygen and hydrogen of the preburner sprays. Each nozzle comprised a liquid jet with exit diameter of 2.3 mm centred in a 8.95 mm diameter air stream. Two liquid flowrates were examined, while the air flowrate was kept constant, resulting in Weber number at the exit of the nozzle around 1100, air-to-liquid momentum ratio 8.6 and 38, velocity ratio 24 and 51, mass flowrate ratio 0.35 and 0.75, liquid jet Reynolds number 10,000 and 21,000 and air jet Reynolds number around 108,000. The air flow characteristics were compared to the flow without liquid injection. Up to 10 air jet diameters from the nozzle exit, individual spray characteristics dominated and maximum Sauter mean diameters, typically around 150 μm, and liquid flux were observed on the geometrical axes of the nozzles. Spray merging was strong in the region between the nozzle axes, where the Sauter mean diameter reduced and the liquid flux and the mean and rms of the fluctuations of the axial velocity of the droplets and the air flow increased relative to the single spray. Downstream of 25 air jet diameters from the nozzle exit, the multiple sprays merged to a single spray-like flow produced by a nozzle located at the centre of the triangular region between the nozzle axes. Reduction of the liquid flowrate by 50 percent, improved atomization by 25 percent, shortened the axial distance from the nozzles where the individual spray characteristics disappeared by 30 percent and increased the air flow turbulence by 20 percent. Droplet coalescence was negligible for high liquid flowrates, but for reduced liquid flowrates coalescence became important and the Sauter mean diameter increased with the axial distance from the exit by around 15 percent. Spray merging increased the air flow turbulence and the local mass fraction distribution of the air in the region between the nozzle axes by around 50 and 40 percent respectively relative to the single sprays, resulting in a fuel rich region with increased gas flow turbulence which may influence the ignition process in the preburner of the space shuttle main engine.
Skip Nav Destination
Article navigation
December 1996
Research Papers
Interaction Between Sprays From Multiple Coaxial Airblast Atomizers
Y. Hardalupas,
Y. Hardalupas
Imperial College of Science, Technology and Medicine, Mechanical Engineering Department, London SW7 2BX, United Kingdom
Search for other works by this author on:
J. H. Whitelaw
J. H. Whitelaw
Imperial College of Science, Technology and Medicine, Mechanical Engineering Department, London SW7 2BX, United Kingdom
Search for other works by this author on:
Y. Hardalupas
Imperial College of Science, Technology and Medicine, Mechanical Engineering Department, London SW7 2BX, United Kingdom
J. H. Whitelaw
Imperial College of Science, Technology and Medicine, Mechanical Engineering Department, London SW7 2BX, United Kingdom
J. Fluids Eng. Dec 1996, 118(4): 762-771 (10 pages)
Published Online: December 1, 1996
Article history
Received:
November 15, 1994
Revised:
August 22, 1996
Online:
January 22, 2008
Article
Article discussed|
View article
Connected Content
Citation
Hardalupas, Y., and Whitelaw, J. H. (December 1, 1996). "Interaction Between Sprays From Multiple Coaxial Airblast Atomizers." ASME. J. Fluids Eng. December 1996; 118(4): 762–771. https://doi.org/10.1115/1.2835507
Download citation file:
Get Email Alerts
Cited By
Optimization of Exhaust Covers in Marine Scrubbers
J. Fluids Eng (December 2022)
Aerodynamics of Sweep in a Tandem-Bladed Subsonic Axial Compressor Rotor
J. Fluids Eng (December 2022)
Numerical Simulations of Fluid Transport in Heterogeneous Darcy–Forchheimer–Brinkman Layers
J. Fluids Eng (December 2022)
Flow Control for a Submerged Inlet
J. Fluids Eng (December 2022)
Related Articles
Modeling Mixture Formation in a Gasoline Direct Injection Engine
J. Appl. Mech (November,2006)
Key Parameters for the Performance of Impaction-Pin Nozzles Used in
Inlet Fogging of Gas Turbine Engines
J. Eng. Gas Turbines Power (April,2007)
Liquid Fuel Placement and Mixing of Generic Aeroengine Premix Module at Different Operating Conditions
J. Eng. Gas Turbines Power (October,2003)
A Comparison of Single and Multiphase Jets in a Crossflow Using Large Eddy Simulations
J. Eng. Gas Turbines Power (January,2007)
Related Proceedings Papers
Related Chapters
A Simple Carburetor
Case Studies in Fluid Mechanics with Sensitivities to Governing Variables
Lay-Up and Start-Up Practices
Consensus on Operating Practices for Control of Water and Steam Chemistry in Combined Cycle and Cogeneration
Antilock-Braking System Using Fuzzy Logic
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3