Measurements of three-dimensional turbulent flow in the exit head section of a shell-and-tube heat exchanger were performed using three-component laser Doppler velocimeter. The test geometry is half of a hemispherical cap with two outlet-tubes and with a cylindrical inlet section. Distributions of the velocity vector field, the three mean velocity components, and the Reynolds stress components are reported, and the complex nature of flow in the head section and in the neighborhood of the outlet-tube is quantified. The radial and the streamwise velocity components are of the same order of magnitude in the neighboring region of the outlet-tubes, and they are not symmetric relative to the center plane intersection of the outlet-tubes. The friction factor that was measured across the exit head section of the heat exchanger decreases as the Reynolds number increases from 25,000 to 50,000. These results are useful for validating turbulent flow simulation codes and are needed for improving the design of the exit head section of shell-and-tube heat exchangers.

Issue Section:
Technical Papers
Keywords:
turbulence, pipe flow, heat exchangers, friction
Topics:
Flow (Dynamics), Heat exchangers, Turbulence, Friction, Reynolds number, Shells, Stress
1.
Chrisholm, D., 1980, Developments in Heat Exchanger Technology—I, Applied Science Publishers, London, England.
2.
Huppan, T., 2000, Heat Exchanger Design Handbook, Marcel Dekker, New York.
3.
Shah, R. K., and London, A. L., 1978, Laminar Flow Forced Convection in Ducts, Academic Press, New York.
4.
Kakac, S., and Liu, H. T., 1997, Heat Exchangers: Selection, Rating, and Thermal Design, CRC Press, New York.
5.
Bremhorst
,
K.
, and
Flint
,
P. J.
,
1991
, “
The Effect of Flow Patterns on the Erosion/Corrosion of Shell and Tube Heat Exchangers
,”
Wear
,
145
, pp.
123
–
135
.
6.
Yu
,
B.
,
Nie
,
J. H.
,
Wang
,
Q. W.
, and
Tao
,
W. Q.
,
1999
, “
Experimental Study on the Pressure Drop and Heat Transfer Characteristics of Tubes with Internal Wave-Like Longitudinal Fins
,”
Heat Mass Transfer
,
35
, pp.
65
–
73
.
7.
Halle, H., Chenoweth, J. M., and Wambsganss, M. W., 1984, “Shell Side Water Flow Pressure Drop Distribution Measurements in an Industrial-Sized Test Heat Exchanger,” In: A Reappraisal of Shell Side Tube Flow in Heat Exchangers,” 22nd Heat Transfer Conference and Exhibition, Niagara Falls, ASME, HTD 36, pp. 37–48.
8.
Zhang
,
C.
,
1994
, “
Numerical Modeling Using a Quasi-Three-Dimensional Procedure for Large Power Plant Condensers
,”
ASME J. Heat Transfer
,
116
, pp.
180
–
188
.
9.
Prithiraj
,
M.
, and
Andrews
,
M. J.
,
1998
, “
Three Dimensional Numerical Simulation of Shell-and-Tube Heat Exchangers—Part I: Foundation and Fluid Mechanics
,”
Numer. Heat Transfer, Part A
,
33
,
799
–
816
.
10.
Tao, W. Q., Nie, J. H., Cheng, P., and Wang, Q. W., 2001, “Numerical Simulation of Three-Dimensional Turbulent Flow in a Complex Geometry, with LDV Experimental Confirmation,” Proceedings of 2nd ICHMT Symposium on Advances in Computational Heat Transfer, Queensland, Australia, pp. 1235–1242.
11.
Miller, R. W., 1996, Flow Measurement Engineering Handbook, 3rd ed., McGraw-Hill, New York.
12.
Wang
,
L. B.
,
Tao
,
W. Q.
,
Wang
,
Q. W.
, and
He
,
Y. L.
,
2001
, “
Experimental and Numerical Study of Turbulent Heat Transfer in Twisted Square Ducts
,”
ASME J. Heat Transfer
,
123
, pp.
868
–
877
.
13.
Barnett, D. O., and Bentley, H. T., 1974, “Statistical Bias of Individual Realization Laser Velocimeters,” Proceedings of the Second International Workshop on Laser Velocimetry, Engineering Extension Series, Purdue University, 144, pp. 428–444.
14.
Moffat
,
R. J.
,
1988
, “
Describing the Uncertainties in Experimental Results
,”
Exp. Therm. Fluid Sci.
,
1
, pp.
3
–
17
.
Copyright © 2004
 by ASME
You do not currently have access to this content.