This paper presents a method for quickly evaluating the effect of changes in bearing location on bearing design for stability of rotating machinery. This method is intended for use by rotating machinery designers to select the “best” bearing locations prior to the bearing design process. The purpose of the method is to improve the design process by separating the problem of determining the “best” bearing locations from that of determining the actual bearing design. The method is independent of the type of bearing employed. For each candidate bearing configuration, the method provides a scalar measure of the relative ability of bearings to meet stability specifications. Within certain limits, the stability specifications are defined by the designer. The scalar measure is used to rank the candidate bearing locations and thereby select the best one. The scalar measure is compared to a practical measure of magnetic bearing design such as the infinity norm of the controller for an example design of a multistage centrifugal compressor.

Issue Section:
Gas Turbines: Structures and Dynamics
Topics:
Bearings, Magnetic bearings, Optimization, Rotors, Bearing design, Design, Scalars, Stability, Machinery, Compressors, Control equipment
1.
Barrett
L. E.
,
1983
, “
The Optimization of Hydrodynamic Journal Bearings for Aerodynamically Excited Flexible Rotor-Bearing Systems
,”
ASME Journal of Mechanical Design
, Vol.
105
, pp.
227
–
232
.
2.
Chiang
H. D.
,
Thorp
J. S.
,
Wang
J. C.
,
Lu
J.
, and
Aubert
B.
,
1992
, “
Optimal Controller Placements in Large-Scale Linear Systems
,”
IEEE Proceedings-D
, Vol.
139
, pp.
79
–
87
.
3.
Choe
K.
, and
Baruh
H.
,
1992
, “
Actuator Placement in Structural Control
,”
AIAA Journal of Guidance and Control
, Vol.
15
, pp.
40
–
48
.
4.
Churchill, R. V., Brown, J. W., and Verhey, R. F., 1974, Complex Variables and Applications, McGraw-Hill, New York.
5.
Dhar, D., Barrett, L. E., and Knospe, C. R., 1991, “Design of Bearings for Rotor Systems Based on Stability,” Proc. Int’l. Symp. on Magnetic Bearing Suspension Tech., NASA Langley Research Ctr., Hampton VA. Aug. 19–23.
6.
Hamdan
A. M. A.
, and
Nayfeh
A. H.
,
1989
, “
Measures of Modal Controllability and Observability
,”
AIAA Journal of Guidance and Control
, Vol.
12
, pp.
421
–
428
.
7.
Johnson
T. L.
, and
Athans
M.
,
1970
, “
On the Design of Optimal Constrained Dynamic Compensators for Linear Constant Systems
,”
IEEE Trans. Automat. Contr.
, Vol.
AC-16
, pp.
658
–
660
.
8.
Kailath, T., 1982, Linear Systems, Prentice Hall, Englewood Cliffs, NJ.
9.
Kim
Y.
, and
Junkins
J. L.
,
1991
, “
Measure of Controllability for Actuator Placement
,”
AIAA Journal of Guidance and Control
, Vol.
14
, pp.
895
–
902
.
10.
Larsonneur, R., and Herzog, R., 1988, “Optimal Design of Structure Predefined Discrete Control for Rotors in Magnetic Bearings,” Proc. 1st Int’l. Symp. on Magnetic Bearings, Springer-Verlag, pp. 347–356.
11.
Laub
A. J.
,
1979
, “
A Schur Method for Solving Algebraic Ricatti Equations
,”
IEEE Trans. Automat. Contr.
, Vol.
AC-24
, pp.
913
–
921
.
12.
Lim
K. B.
,
1992
, “
Method for Optimal Actuator and Sensor Placement for Large Flexible Structures
,”
AIAA Journal of Guidance and Control
, Vol.
15
, pp.
49
–
57
.
13.
Maslen, E. H., 1991a, “Magnetic Bearing Synthesis for Rotating Machinery,” Ph.D. dissertation, University of Virginia, Charlottesville, VA.
14.
Maslen, E. H., 1991b, “Controllability of Rotors,” Proc. ROMAG ’91 Conference on Magnetic Bearings and Dry Gas Seals, Alexandria, VA.
15.
Molinari
B. P.
,
1977
, “
The Time Invariant Linear Quadratic Optimal Control Problem
,”
Automatica
, Vol.
13
, pp.
347
–
357
.
16.
Moore
B. C.
,
1981
, “
Principal Component Analysis in Linear Systems: Controllability, Observability and Model Reduction
,”
IEEE Trans. Automat. Contr.
, Vol.
AC-29
, pp.
17
–
31
.
17.
Srinivasan, S., 1993, “A Stability Based Method for Selecting Bearing Locations in Rotor-Bearing Systems,” Ph.D. Dissertation, Univ. of Virginia, Charlottesville, VA.
18.
Tarokh, M., 1990, “Measures for Controllability and Eigenvalue Mobility,” Proc. 29th Conference on Decision and Control, pp. 1143–1148.
19.
Vishwanathan
C. N.
,
Longman
R. W.
, and
Likins
P. W.
,
1984
, “
A Degree of Controllability Definition: Fundamental Concepts and Application to Modal Systems
,”
AIAA Journal of Guidance and Control
, Vol.
7
, pp.
222
–
230
.
This content is only available via PDF.
Copyright © 1997
 by The American Society of Mechanical Engineers
You do not currently have access to this content.