The influence of a honeycomb facing on the heat transfer of a stepped labyrinth seal with geometry typical for modern jet engines was investigated. Heat transfer measurements were obtained for both a smooth stator and a stator lined with a honeycomb structure. In addition, an LDV system was used with the scaled up geometry to obtain a high local resolution of the velocity distribution in the seal. The experiments covered a wide range of pressure ratios and gap widths, typical for engine operating conditions. Local heat transfer coefficients were calculated from the measured wall and gas temperatures using a finite element code. By averaging the local values, mean heat transfer coefficients were determined and correlations for the global Nusselt numbers were derived for the stator and the rotor. The LDV results showed strong geometrical effects of the honeycomb structure on the development of the flow fields for the honeycomb seal. The distribution of the local heat transfer coefficients are compatible with the flow features identified by the LDV results and reveal a significantly reduced heat transfer with the honeycomb facing compared to the smooth facing.

Issue Section:
Gas Turbines: Heat Transfer and Turbomachinery
Keywords:
seals (stoppers), heat transfer, gas turbines, friction
Topics:
Flow (Dynamics), Heat transfer, Heat transfer coefficients, Honeycomb structures, Rotors, Stators, Pressure, Temperature, Geometry
1.
Komotori, K., and Miyake, K., 1977, “Leakage Characteristics of Labyrinth Seals With High Rotating Speed,” 1977 Tokyo Joint Gas Turbine Congress.
2.
Morrison, G. L., and Daesung, Chi, 1985, “Incompressible Flow in Stepped Labyrinth Seals,” ASME Paper 85-FE-4.
3.
Morrison
,
G. L.
,
Johnson
,
M. C.
, and
Tatterson
,
G. B.
,
1991
, “
3-D Laser Anemometer Measurements in a Labyrinth Seal
,”
ASME J. Eng. Gas Turbines Power
,
113
, pp.
119
–
125
.
4.
Wittig
,
S.
,
Jacobsen
,
K.
,
Schelling
,
U.
, and
Kim
,
S.
,
1988
, “
Heat Transfer in Stepped Labyrinth Seals
,”
ASME J. Eng. Gas Turbines Power
,
110
, pp.
63
–
69
.
5.
Wittig, S., Schelling U., Jacobsen, K., and Kim, S., 1987 “Numerical Predictions and Measurements of Discharge Coefficients in Labyrinth Seals,” ASME Paper 87-GT-188.
6.
Rhode, D. L., and Hibbs, R. I., 1989 “A Comparative Investigation of Corresponding Annular and Labyrinth Seal Flowfields,” ASME Paper 89-GT-195.
7.
Rhode
,
D. L.
,
Johnson
,
J. W.
, and
Broussard
,
D. H.
,
1997
, “
Flow Visualization and Leakage Measurements of Stepped Labyrinth Seals, Parts 1 and 2
,”
ASME J. Turbomach.
,
119
, pp.
839
–
848
.
8.
Prasad, B. V. S. S. S., Sethu Manavalan, D. L., Nanjunda Rao, N. V., 1997, “Computational and Experimental Investigations of Straight-Through Labyrinth Seals,” ASME Paper 97-GT-326.
9.
Stocker, H. L., 1978, “Determining and Improving Labyrinth Seal Performance in Current and Advanced High Performance Gas Turbines,” AGARD-CP-237 Conference Proceedings, pp. 13/1–13/22.
10.
Zimmermann, H., and Wolff, K. H., 1998, “Air System Correlations, Part 1: Labyrinth Seals,” ASME Paper 98-GT-206.
11.
Brownell
,
J. B.
,
Millward
,
J. A.
, and
Parker
,
R. J.
,
1989
, “
Non-Intrusive Investigations Into Life-Size Labyrinth Seal Flow Fields
,”
ASME J. Eng. Gas Turbines Power
,
111
, pp.
335
–
342
.
12.
Childs
,
D.
,
Elrod
,
D.
, and
Hale
,
K.
1989
, “
Annular Honeycomb Seals: Test Results for Leakage and Rotordynamic Coefficients; Comparison to Labyrinth and Smooth Configurations
,”
ASME J. Tribol.
,
111
, pp.
293
–
301
.
13.
Ha
,
T. W.
,
Morrison
,
G. L.
, and
Childs
,
D. W.
,
1992
, “
Friction-Factor Characteristics for Narrow Channels With Honeycomb Surfaces
,”
ASME J. Tribol.
,
114
, pp.
714
–
721
.
14.
Ha
,
T. W.
, and
Childs
,
D. W.
,
1992
, “
Friction-Factor Data for Flat-Plate Tests of Smooth and Honeycomb Surfaces
,”
ASME J. Tribol.
,
114
, pp.
722
–
730
.
15.
Millward
,
J. A.
, and
Edwards
,
M. F.
,
1994
, “
Windage Heating of Air Passing Through Labyrinth Seals
,”
ASME J. Turbomach.
,
118
, pp.
415
–
419
.
16.
Kapinos
,
V. M.
, and
Gura
,
L. A.
,
1970
, “
Investigation of Heat Transfer in Labyrinth Glands on Static Models
,”
Therm. Eng.
,
17
, No.
11
, pp.
54
–
56
.
17.
Kapinos
,
V. M.
, and
Gura
,
L. A.
,
1973
, “
Heat Transfer of a Stepped Labyrinth Seal
,”
Therm. Eng.
,
20
, No.
6
, pp.
28
–
32
.
18.
Waschka
,
W.
,
Wittig
,
S.
, and
Kim
,
S.
,
1992
, “
Influence of High Rotational Speeds on the Heat Transfer and Discharge Coefficients in Labyrinth Seals
,”
ASME J. Turbomach.
,
114
, pp.
462
–
468
.
19.
Waschka, W., Wittig, S., Kim, S., and Scherer, T., 1993, “Heat Transfer and Leakage in High-Speed Rotating Stepped Labyrinth Seals,” AGARD-CP-527, pp. 26/1–26/10.
20.
Jakoby, R., Maeng, D. J., Kim, S., and Wittig, S., 1997, “3D LDA-Measurements in Rotating Turbine Disk Systems,” Laser Anemometry Advanced Applications, Proceedings of the 7th International Conference, Karlsruhe, Sept. 8–11.
21.
Schramm
,
V.
,
Willenborg
,
K.
,
Kim
,
S.
, and
Wittig
,
S.
,
2002
, “
Influence of a Honeycomb Facing on the Flow Field and Discharge Behavior of a Stepped Labyrinth Seal
,”
ASME J. Eng. Gas Turbines Power
,
124
, pp.
140
–
146
.
Copyright © 2002
 by ASME
You do not currently have access to this content.