Cavitation and turbulence inside a diesel injector play a critical role in primary spray breakup and development processes. The study of cavitation in realistic injectors is challenging, both theoretically and experimentally, since the associated two-phase flow field is turbulent and highly complex, characterized by large pressure gradients and small orifice geometries. We report herein a computational investigation of the internal nozzle flow and cavitation characteristics in a diesel injector. A mixture based model in FLUENT V6.2 software is employed for simulations. In addition, a new criterion for cavitation inception based on the total stress is implemented, and its effectiveness in predicting cavitation is evaluated. Results indicate that under realistic diesel engine conditions, cavitation patterns inside the orifice are influenced by the new cavitation criterion. Simulations are validated using the available two-phase nozzle flow data and the rate of injection measurements at various injection pressures (800–1600 bar) from the present study. The computational model is then used to characterize the effects of important injector parameters on the internal nozzle flow and cavitation behavior, as well as on flow properties at the nozzle exit. The parameters include injection pressure, needle lift position, and fuel type. The propensity of cavitation for different on-fleet diesel fuels is compared with that for n-dodecane, a diesel fuel surrogate. Results indicate that the cavitation characteristics of n-dodecane are significantly different from those of the other three fuels investigated. The effect of needle movement on cavitation is investigated by performing simulations at different needle lift positions. Cavitation patterns are seen to shift dramatically as the needle lift position is changed during an injection event. The region of significant cavitation shifts from top of the orifice to bottom of the orifice as the needle position is changed from fully open (0.275 mm) to nearly closed (0.1 mm), and this behavior can be attributed to the effect of needle position on flow patterns upstream of the orifice. The results demonstrate the capability of the cavitation model to predict cavitating nozzle flows in realistic diesel injectors and provide boundary conditions, in terms of vapor fraction, velocity, and turbulence parameters at the nozzle exit, which can be coupled with the primary breakup simulation.
Skip Nav Destination
e-mail: ssom1@uic.edu
Article navigation
April 2010
Research Papers
Investigation of Nozzle Flow and Cavitation Characteristics in a Diesel Injector
S. Som,
S. Som
Department of Mechanical and Industrial Engineering,
e-mail: ssom1@uic.edu
University of Illinois at Chicago
, 842 West Taylor Street, Chicago, IL 60607-7022
Search for other works by this author on:
S. K. Aggarwal,
S. K. Aggarwal
Department of Mechanical and Industrial Engineering,
University of Illinois at Chicago
, 842 West Taylor Street, Chicago, IL 60607-7022
Search for other works by this author on:
E. M. El-Hannouny,
E. M. El-Hannouny
Center for Transportation Research,
Argonne National Laboratory
, Argonne, IL 60439
Search for other works by this author on:
D. E. Longman
D. E. Longman
Center for Transportation Research,
Argonne National Laboratory
, Argonne, IL 60439
Search for other works by this author on:
S. Som
Department of Mechanical and Industrial Engineering,
University of Illinois at Chicago
, 842 West Taylor Street, Chicago, IL 60607-7022e-mail: ssom1@uic.edu
S. K. Aggarwal
Department of Mechanical and Industrial Engineering,
University of Illinois at Chicago
, 842 West Taylor Street, Chicago, IL 60607-7022
E. M. El-Hannouny
Center for Transportation Research,
Argonne National Laboratory
, Argonne, IL 60439
D. E. Longman
Center for Transportation Research,
Argonne National Laboratory
, Argonne, IL 60439J. Eng. Gas Turbines Power. Apr 2010, 132(4): 042802 (12 pages)
Published Online: January 15, 2010
Article history
Received:
November 13, 2008
Revised:
April 6, 2009
Online:
January 15, 2010
Published:
January 15, 2010
Citation
Som, S., Aggarwal, S. K., El-Hannouny, E. M., and Longman, D. E. (January 15, 2010). "Investigation of Nozzle Flow and Cavitation Characteristics in a Diesel Injector." ASME. J. Eng. Gas Turbines Power. April 2010; 132(4): 042802. https://doi.org/10.1115/1.3203146
Download citation file:
Get Email Alerts
Experimental Identification Of Blade Tip Rub Forces At Engine Relevant Temperatures And Speeds
J. Eng. Gas Turbines Power
Study Of Tandem Rotor Dual Wake Interaction With Downstream Stator Under Unsteady Numerical Approach
J. Eng. Gas Turbines Power
Experimental Design Validation of a Swirl-Stabilized Burner With Fluidically Variable Swirl Number
J. Eng. Gas Turbines Power (April 2025)
Experimental Characterization of a Bladeless Air Compressor
J. Eng. Gas Turbines Power (April 2025)
Related Articles
A Numerical Investigation of Transient Flow and Cavitation Within Minisac and Valve-Covered Orifice Diesel Injector Nozzles
J. Eng. Gas Turbines Power (May,2010)
Simulation and Experimental Analysis of Diesel Fuel-Injection Systems With a Double-Stage Injector
J. Eng. Gas Turbines Power (April,1999)
Numerical Analysis Versus Experimental Investigation of a Distributor-Type Diesel Fuel-Injection System
J. Eng. Gas Turbines Power (October,1994)
Coupled Simulations of Nozzle Flow, Primary Fuel Jet Breakup, and Spray Formation
J. Eng. Gas Turbines Power (October,2005)
Related Proceedings Papers
Related Chapters
Antilock-Braking System Using Fuzzy Logic
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3
In-Nozzle Cavitation-Induced Orifice-to-Orifice Variations Using Real Injector Geometry and Gasoline-Like Fuels
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Fuel Nozzle Geometry Effects on Cavitation and Spray Behavior at Diesel Engine Conditions
Proceedings of the 10th International Symposium on Cavitation (CAV2018)