A detailed analysis of experimental and numerical results for flow and heat transfer in similar offset strip-fin geometries is presented. Surface-average heat transfer and pressure drop, local Nusselt numbers and skin friction coefficients on the fin surface, instantaneous flow structures, and local time-averaged velocity profiles are contrasted for a range of Reynolds numbers using both prior and new experimental and numerical results. This contrast verifies that a two-dimensional unsteady numerical simulation captures the important features of the flow and heat transfer for a range of conditions. However, flow three-dimensionality appears to become important for Reynolds numbers greater than about 1300, and thermal boundary conditions are important for Reynolds numbers below 1000. The results indicate that boundary layer development, flow separation and reattachment, wake formation, and vortex shedding are all important in this complex geometry.
Issue Section:
Heat Exchangers
1.
Amon
C. H.
Mikic
B. B.
1991
, “Spectral Element Simulations of Unsteady Forced Convective Heat Transfer: Application to Compact Heat Exchanger Geometries
,” Numerical Heat Transfer
, Part A, Vol. 19
, pp. 1
–19
.2.
Chen
Y. N.
1968
, “Flow-Induced Vibration and Noise in Tube-Bank Heat Exchangers Due to von Karman Streets
,” J. of Engineering for Industry
, Vol. 90(b)
, pp. 134
–146
.3.
DeJong
N. C.
Jacobi
A. M.
1997
, “An Experimental Study of Flow and Heat Transfer in Parallel-Plate Arrays: Local, Row-by-Row and Surface Average Behavior
,” Int. J. Heat Mass Transfer
, Vol. 40
, No. 6
, pp. 1365
–1378
.4.
Ghaddar
N. K.
Karniadakis
G. E.
Patera
A. T.
1986
, “A Conservative Isoparametric Spectral Element Method for Forced Convection: Application to Fully Developed Flow in Periodic Geometries
,” Numerical Heat Transfer
, Vol. 9
, pp. 277
–300
.5.
Goldstein
R. J.
Cho
H. H.
1995
, “A Review of Mass Transfer Measurements Using Naphthalene Sublimation
,” Exp. Thermal Fluid Sci.
, Vol. 10
, pp. 416
–434
.6.
Joshi
H. M.
Webb
R. L.
1987
, “Heat Transfer and Friction in the Offset Strip-Fin Heat Exchanger
,” Int. J. Heat Mass Transfer
, Vol. 30
, pp. 69
–83
.7.
Kearney
S. P.
Jacobi
A. M.
1996
, “Local Convective Behavior and Fin Efficiency in Shallow Banks of Inline and Staggered, Annularly Finned Tubes
,” ASME JOURNAL OF HEAT TRANSFER
, Vol. 118
, pp. 317
–326
.8.
Kiya
M.
Sasaki
K.
1985
, “Structure of Large-Scale Vortices and Unsteady Reverse Flow in the Reattaching Zone of a Turbulent Separation Bubble
,” J. Fluid Mechanics
, Vol. 154
, pp. 463
–491
.9.
Kline
S. J.
McClintock
F. A.
1953
, “Describing Uncertainties in Single Sample Experiments
,” Mechanical Engineering
, Vol. 75
, pp. 3
–8
.10.
Manglik
R. M.
Bergles
A. E.
1995
, “Heat Transfer and Pressure Drop Correlations for the Rectangular Offset Strip Fin Compact Heat Exchanger
,” Exp. Thermal Fluid Sci.
, Vol. 10
, pp. 171
–180
.11.
Ota
T.
Nishiyama
H.
1987
, “A Correlation of Maximum Turbulent Heat Transfer Coefficient in Reattachment Flow Region
,” Int. J. Heat Mass Transfer
, Vol. 30
, pp. 1193
–1200
.12.
Patankar
S. V.
Prakash
C.
1981
, “An Analysis of the Effect of Plate Thickness on Laminar Flow and Heat Transfer in Interrupted-Plate Passages
,” Int. J. Heat Mass Transfer
, Vol. 24
, pp. 51
–58
.13.
Souza Mendes
P. R.
1991
, “The Naphthalene Sublimation Technique
,” Exp. Thermal Fluid Sci.
, Vol. 4
, pp. 510
–523
.14.
Sparrow
E. M.
Hajiloo
A.
1980
, “Measurements of Heat Transfer and Pressure Drop for an Array of Staggered Plates Aligned Parallel to an Air Flow
,” ASME JOURNAL OF HEAT TRANSFER
, Vol. 102
, pp. 426
–432
.15.
Sparrow
E. M.
Kang
S. S.
Chuck
W.
1987
, “Relation Between the Points of Flow Reattachment and Maximum Heat Transfer for Regions of Flow Separation
,” Int. J. Heat Mass Transfer
, Vol. 30
, pp. 1237
–1246
.16.
Sparrow
E. M.
Liu
C. H.
1979
, “Heat Transfer, Pressure Drop and Performance Relationships for In-Line, Staggered, and Continuous Plate Heat Exchangers
,” Int. J. Heat Mass Transfer
, Vol. 22
, pp. 1613
–1624
.17.
Suzuki
K.
Hirai
E.
Miyake
T.
1985
, “Numerical and Experimental Studies on a Two-Dimensional Model of an Offset-Strip-Fin Type Compact Heat Exchanger Used at Low Reynolds Number
,” Int. J. Heat Mass Transfer
, Vol. 28
, No. 4
, pp. 823
–836
.18.
Vogel
J. C.
Eaton
J. K.
1985
, “Combined Heat Transfer and Fluid Dynamic Measurements Downstream of a Backward-Facing Step
,” ASME JOURNAL OF HEAT TRANSFER
, Vol. 107
, pp. 922
–929
.19.
Wieting
A. R.
1975
, “Empirical Correlations for Heat Transfer and Flow Friction Characteristics of Rectangular Offset-Fin Plate-Fin Heat Exchangers
,” ASME JOURNAL OF HEAT TRANSFER
, Vol. 97
, pp. 488
–490
.20.
Xi, G. N., Futagami, S., Hagiwara, Y., and Suzuki, K., 1991, “Flow and Heat Transfer Characteristics of Offset-Fin Array in the Middle Reynolds Number Range,” ASME/JSME Thermal Engineering Proceedings, Vol. 3, pp. 151–156.
21.
Xi, G. N., Suzuki, K., Hagiwara, Y., and Murata, T., 1990, “Experimental Study on Heat Transfer Characteristics of Offset Fin Arrays—Effect of Fin Thickness in the Low and Middle Ranges of Reynolds Number,” Heat Transfer 1990, Vol. 4, pp. 81–86.
22.
Zhang
L. W.
Tafti
D. K.
Najjar
F. M.
Balachandar
S.
1997
a, “Computations of Flow and Heat Transfer in Parallel-Plate Fin Heat Exchangers on the CM-5: Effects of Flow Unsteadiness and Three-Dimensionality
,” Int. J. Heat Mass Transfer
, Vol. 40
, No. 6
, pp. 1325
–1341
.23.
Zhang
L. W.
Balachandar
S.
Tafti
D. K.
Najjar
F. M.
1997
b, “Heat Transfer Enhancement Mechanisms in Inline and Staggered Parallel-Plate Fin Heat Exchangers
,” Int. J. Heat Mass Transfer
, Vol. 40
, No. 10
, pp. 2307
–2325
.24.
Zhang
L. W.
Balachandar
S.
Tafti
D. K.
1997
c, “Effect of Three-Dimensionality on Predicting Flow and Heat Transfer in Parallel-Plate Fin Heat Exchangers
,” Num. Heat Transfer
, Part A, Vol. 31
, pp. 327
–353
.
This content is only available via PDF.
Copyright © 1998
by The American Society of Mechanical Engineers
You do not currently have access to this content.
