This paper offers an experimental study of the microcutting mechanisms in marble grinding to aid the optimization of the marble grinding process. The necessity for investigating these mechanisms is dictated by the increased use of marble in many applications and the fact that grinding and polishing processes are the dominant technologies used to meet surface finish requirements in this natural material. The experiments are aimed at the determination of the normal component of the cutting force and of the grain traces in microcutting with a single diamond grain. The investigations carried out make provisions for establishing critical grain penetration and cutting depths and allow the prediction of the normal cutting force component as a function of grain penetration speed and depth.
Skip Nav Destination
e-mail: ltanovic@mas.bg.ac.rs
e-mail: pbojanic@mas.bg.ac.rs
e-mail: rpuzovic@mas.bg.ac.rs
e-mail: atmu@ism.kiev.ua
Article navigation
December 2009
Technical Briefs
Experimental Investigation of Microcutting Mechanisms in Marble Grinding
LJ. Tanovic,
LJ. Tanovic
Professor
Department of Production Engineering,
e-mail: ltanovic@mas.bg.ac.rs
Faculty of Mechanical Engineering
, Kraljice Marije 16, Belgrade 11120, Serbia
Search for other works by this author on:
P. Bojanic,
P. Bojanic
Professor
Department of Production Engineering,
e-mail: pbojanic@mas.bg.ac.rs
Faculty of Mechanical Engineering
, Kraljice Marije 16, Belgrade 11120, Serbia
Search for other works by this author on:
R. Puzovic,
R. Puzovic
Assistant Professor
Department of Production Engineering,
e-mail: rpuzovic@mas.bg.ac.rs
Faculty of Mechanical Engineering
, Kraljice Marije 16, Belgrade 11120, Serbia
Search for other works by this author on:
S. Klimenko
S. Klimenko
Professor
V. Bakul Institute for Superhard Materials,
e-mail: atmu@ism.kiev.ua
National Academy of Sciences of Ukraine
, Avtozavodsky Strasse 2, Kiev 07074, Ukraine
Search for other works by this author on:
LJ. Tanovic
Professor
Department of Production Engineering,
Faculty of Mechanical Engineering
, Kraljice Marije 16, Belgrade 11120, Serbiae-mail: ltanovic@mas.bg.ac.rs
P. Bojanic
Professor
Department of Production Engineering,
Faculty of Mechanical Engineering
, Kraljice Marije 16, Belgrade 11120, Serbiae-mail: pbojanic@mas.bg.ac.rs
R. Puzovic
Assistant Professor
Department of Production Engineering,
Faculty of Mechanical Engineering
, Kraljice Marije 16, Belgrade 11120, Serbiae-mail: rpuzovic@mas.bg.ac.rs
S. Klimenko
Professor
V. Bakul Institute for Superhard Materials,
National Academy of Sciences of Ukraine
, Avtozavodsky Strasse 2, Kiev 07074, Ukrainee-mail: atmu@ism.kiev.ua
J. Manuf. Sci. Eng. Dec 2009, 131(6): 064507 (5 pages)
Published Online: December 4, 2009
Article history
Received:
April 7, 2009
Revised:
November 5, 2009
Online:
December 4, 2009
Published:
December 4, 2009
Citation
Tanovic, L., Bojanic, P., Puzovic, R., and Klimenko, S. (December 4, 2009). "Experimental Investigation of Microcutting Mechanisms in Marble Grinding." ASME. J. Manuf. Sci. Eng. December 2009; 131(6): 064507. https://doi.org/10.1115/1.4000619
Download citation file:
Get Email Alerts
Cited By
On-Orbit Processing and Hardware Performance of Microgravity Hydrothermal Synthesis for Graphene Aerogel
J. Manuf. Sci. Eng (December 2024)
A Review on Metallic Drilling Burrs: Geometry, Formation, and Effect on the Mechanical Strength of Metallic Assemblies
J. Manuf. Sci. Eng (April 2025)
Related Articles
Experimental Investigation of Microcutting Mechanisms in Granite Grinding
J. Manuf. Sci. Eng (April,2011)
Influence of Grinding Parameters on Glass Workpieces Surface Finish Using Response Surface Methodology
J. Manuf. Sci. Eng (August,2011)
Forces and Energy in Circular Sawing and Grinding of Granite
J. Manuf. Sci. Eng (February,2001)
Wear Mechanisms in Ceramic Machining
Appl. Mech. Rev (June,1994)
Related Chapters
Cut Edge Behavior
New Advanced High Strength Steels: Optimizing Properties
Cutting Performance and Wear Mechanism of Cutting Tool in Milling of High Strength Steel 34CrNiMo6
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)
Dynamic One-Dimensional Cutting Stock Optimization and the Generation of Leftovers
International Conference on Computer and Automation Engineering, 4th (ICCAE 2012)