Abstract
This paper presents a study of the wear of high-speed steel cutting tools modified mechanochemically by shot peening their rake faces with a mixture of Al2O3 and Cu2S particles. This treatment has been recently proved to reduce cutting forces significantly, but little is known about the wear resistance of the modified tools. To pave the way for practical implementation of this technology, here we bridge this gap. Orthogonal cutting tests performed under base oil lubrication demonstrate at least a twofold increase in the tool life compared to the untreated references. This is attributed to the formation of iron sulfide and its ability to retain oil at the cutting interface, which results in lower stresses and temperature. This environmentally friendly technique shows good potential to lower manufacturing costs, reduce energy consumption, and improve machining quality.
References
1.
Czichos
, H.
, 1978
, Tribology: A Systems Approach to the Science and Technology of Friction, Lubrication, and Wear
, Elsevier
, New York
.2.
Varenberg
, M.
, 2013
, “Towards a Unified Classification of Wear
,” Friction
, 1
(4
), pp. 333
–340
. 3.
Krolczyk
, G.
, Nieslony
, P.
, and Legutko
, S.
, 2015
, “Determination of Tool Life and Research Wear During Duplex Stainless Steel Turning
,” Arch. Civil Mech. Eng.
, 15
(2
), pp. 347
–354
. 4.
Mia
, M.
, Gupta
, M. K.
, Lozano
, J. A.
, Carou
, D.
, Pimenov
, D. Y.
, Królczyk
, G.
, Khan
, A. M.
, and Dhar
, N. R.
, 2019
, “Multi-objective Optimization and Life Cycle Assessment of Eco-Friendly Cryogenic N2 Assisted Turning of Ti–6Al–4V
,” J. Cleaner Prod.
, 210
, pp. 121
–133
. 5.
Kim
, D. M.
, Lee
, I.
, Kim
, S. K.
, Kim
, B. H.
, and Park
, H. W.
, 2016
, “Influence of a Micropatterned Insert on Characteristics of the Tool-Workpiece Interface in a Hard Turning Process
,” J. Mater. Process. Technol.
, 229
, pp. 160
–171
. 6.
Kümmel
, J.
, Braun
, D.
, Gibmeier
, J.
, Schneider
, J.
, Greiner
, C.
, Schulze
, V.
, and Wanner
, A.
, 2015
, “Study on Micro Texturing of Uncoated Cemented Carbide Cutting Tools for Wear Improvement and Built-Up Edge Stabilisation
,” J. Mater. Process. Technol.
, 215
, pp. 62
–70
. 7.
Zhu
, D.
, Qu
, N.
, Li
, H.
, Zeng
, Y.
, Li
, D.
, and Qian
, S.
, 2009
, “Electrochemical Micromachining of Microstructures of Micro Hole and Dimple Array
,” CIRP Ann.
, 58
(1
), pp. 177
–180
. 8.
Qi
, Y.
, Nguyen
, V.
, Melkote
, S.
, and Varenberg
, M.
, 2020
, “Wear of WC Inserts Textured by Shot Peening and Electrical Discharge Machining
,” Wear
, 452–453
, p. 203279
. 9.
Ma
, J.
, Duong
, N. H.
, and Lei
, S.
, 2015
, “Numerical Investigation of the Performance of Microbump Textured Cutting Tool in Dry Machining of AISI 1045 Steel
,” J. Manuf. Process.
, 19
, pp. 194
–204
. 10.
Su
, Y.
, Li
, Z.
, Li
, L.
, Wang
, J.
, Gao
, H.
, and Wang
, G.
, 2017
, “Cutting Performance of Micro-Textured Polycrystalline Diamond Tool in Dry Cutting
,” J. Manuf. Process.
, 27
, pp. 1
–7
. 11.
Niketh
, S.
, and Samuel
, G.
, 2017
, “Surface Texturing for Tribology Enhancement and Its Application on Drill Tool for the Sustainable Machining of Titanium Alloy
,” J. Cleaner Prod.
, 167
, pp. 253
–270
. 12.
Niketh
, S.
, and Samuel
, G. L.
, 2018
, “Drilling Performance of Micro Textured Tools Under Dry, Wet and MQL Condition
,” J. Manuf. Process.
, 32
, pp. 254
–268
. 13.
Sugihara
, T.
, and Enomoto
, T.
, 2017
, “Performance of Cutting Tools With Dimple Textured Surfaces: A Comparative Study of Different Texture Patterns
,” Precis. Eng.
, 49
, pp. 52
–60
. 14.
Chen
, Y.
, Guo
, X.
, Zhang
, K.
, Guo
, D.
, Zhou
, C.
, and Gai
, L.
, 2019
, “Study on the Surface Quality of CFRP Machined by Micro-Textured Milling Tools
,” J. Manuf. Process.
, 37
, pp. 114
–123
. 15.
Alagan
, N. T.
, Zeman
, P.
, Hoier
, P.
, Beno
, T.
, and Klement
, U.
, 2019
, “Investigation of Micro-Textured Cutting Tools Used for Face Turning of Alloy 718 With High-Pressure Cooling
,” J. Manuf. Process.
, 37
, pp. 606
–616
. 16.
Gäbler
, J.
, and Pleger
, S.
, 2010
, “Precision and Micro CVD Diamond-Coated Grinding Tools
,” Int. J. Mach. Tools Manuf.
, 50
(4
), pp. 420
–424
. 17.
De Cristofaro
, S.
, Funaro
, N.
, Feriti
, G.
, Rostagno
, M.
, Comoglio
, M.
, Merlo
, A.
, Stefanini
, C.
, and Dario
, P.
, 2012
, “High-Speed Micro-Milling: Novel Coatings for Tool Wear Reduction
,” Int. J. Mach. Tools Manuf.
, 63
, pp. 16
–20
. 18.
Russell
, W. C.
, Malshe
, A. P.
, Yedave
, S. N.
, and Brown
, W. D.
, 2003
, “CBN-TiN Composite Coating Using a Novel Combinatorial Method—Structure and Performance in Metal Cutting
,” ASME J. Manuf. Sci. Eng.
, 125
(3
), pp. 431
–435
. 19.
Grigoriev
, S.
, Vereschaka
, A.
, Fyodorov
, S.
, Sitnikov
, N.
, and Batako
, A.
, 2017
, “Comparative Analysis of Cutting Properties and Nature of Wear of Carbide Cutting Tools With Multi-Layered Nano-Structured and Gradient Coatings Produced by Using of Various Deposition Methods
,” Int. J. Adv. Manuf. Technol.
, 90
(9–12
), pp. 3421
–3435
. 20.
Wu
, W.
, Chen
, W.
, Yang
, S.
, Lin
, Y.
, Zhang
, S.
, Cho
, T.-Y.
, Lee
, G.
, and Kwon
, S.-C.
, 2015
, “Design of AlCrSiN Multilayers and Nanocomposite Coating for HSS Cutting Tools
,” Appl. Surf. Sci.
, 351
, pp. 803
–810
. 21.
Kalpakjian
, S.
, and Schmid
, S. R.
, 2008
, Manufacturing Processes for Engineering Materials
, Pearson Education
, Upper Saddle River
.22.
Fleischauer
, P. D.
, 1987
, “Fundamental Aspects of the Electronic Structure, Materials Properties and Lubrication Performance of Sputtered MoS2 Films
,” Thin Solid Films
, 154
(1–2
), pp. 309
–322
. 23.
Liu
, Y.-R.
, Liu
, J.-J.
, and Du
, Z.
, 1999
, “The Cutting Performance and Wear Mechanism of Ceramic Cutting Tools With MoS2 Coating Deposited by Magnetron Sputtering
,” Wear
, 231
(2
), pp. 285
–292
. 24.
Ze
, W.
, Jianxin
, D.
, Yang
, C.
, Youqiang
, X.
, and Jun
, Z.
, 2012
, “Performance of the Self-Lubricating Textured Tools in Dry Cutting of Ti–6Al–4V
,” Int. J. Adv. Manuf. Technol.
, 62
(9–12
), pp. 943
–951
. 25.
Varenberg
, M.
, Ryk
, G.
, Yakhnis
, A.
, Kligerman
, Y.
, Kondekar
, N.
, and McDowell
, M. T.
, 2016
, “Mechano-Chemical Surface Modification with Cu2S: Inducing Superior Lubricity
,” Tribol. Lett.
, 64
(2
), p. 28
. 26.
Qi
, Y.
, Nguyen
, V.
, Melkote
, S.
, and Varenberg
, M.
, 2019
, “Mechano-Chemical Surface Modification of High-Speed Steel Cutting Tools
,” ASME J. Manuf. Sci. Eng.
, 141
(4
), p. 041009
. 27.
International Standard ISO 3685
, 1993
, “Tool-Life Testing With Single-Point Turning Tools
,” International Organization for Standardization
.28.
García-Cruz
, I.
, Valencia
, D.
, Klimova
, T.
, Oviedo-Roa
, R.
, Martínez-Magadán
, J. M.
, Gómez-Balderas
, R.
, and Illas
, F.
, 2008
, “Proton Affinity of S-Containing Aromatic Compounds: Implications for Crude Oil Hydrodesulfurization
,” J. Mol. Catal. A: Chem.
, 281
(1
), pp. 79
–84
. 29.
Qi
, Y.
, Nguyen
, V.
, Melkote
, S.
, and Varenberg
, M.
, 2022
, “Analysis of Mechanochemical Reaction in Dual Shot Peening
,” J. Manuf. Sci. Eng. Trans. ASME
, 144
(4
), p. 041016
. 30.
Chen
, W.
, 2000
, “Cutting Forces and Surface Finish When Machining Medium Hardness Steel Using CBN Tools
,” Int. J. Mach. Tools Manuf.
, 40
(3
), pp. 455
–466
. 31.
Bartz
, W. J.
, 2001
, “Ecological and Environmental Aspects of Cutting Fluids
,” Lubr. Eng.
, 57
(3
), pp. 13
–16
.Copyright © 2022 by ASME
You do not currently have access to this content.
