Finite element models in orthogonal cutting are presented in order to examine the influences of exit angles of the workpiece, tool rake angles, and backup materials on burr formation processes in 304 L stainless steel in particular. Based on the metal-cutting simulation procedure proposed by the authors, a series of stress and strain contours and final burr/breakout configurations are obtained. The burr formation mechanisms with respect to five different exit angles are found, and duration of the burr formation process increases with an increase of exit angle, resulting in different burr/breakout configurations. Based on the development of negative shear stress in front of the tool tip, the tool tip damage, what is called “chipping,” is investigated. Also, with fixed cutting conditions and workpiece exit geometry, the influence of the rake angle is found to be closely related to the rate of plastic work in steady-state cutting because the larger the rate of plastic work in steady-state cutting, the earlier the burr initiation commences. Furthermore, in order to effectively minimize the burr size, three cases of backup material influences on burr formation processes are examined. It is found that the burr size can be effectively minimized when the backup material supports the workpiece only up to the predefined machined surface. [S0094-4289(00)01402-X]
Skip Nav Destination
Article navigation
April 2000
Technical Papers
A Study of Burr Formation Processes Using the Finite Element Method: Part II—The Influences of Exit Angle, Rake Angle, and Backup Material on Burr Formation Processes
I. W. Park,
I. W. Park
Integrated Surgical Systems, Inc., 1850 Research Park Dr., Davis, CA 95616
Search for other works by this author on:
D. A. Dornfeld, Fellow ASME
D. A. Dornfeld, Fellow ASME
Department of Mechanical Engineering, University of California, Berkeley, Berkeley, CA 94270-1740
Search for other works by this author on:
I. W. Park
Integrated Surgical Systems, Inc., 1850 Research Park Dr., Davis, CA 95616
D. A. Dornfeld, Fellow ASME
Department of Mechanical Engineering, University of California, Berkeley, Berkeley, CA 94270-1740
Contributed by the Materials Division for Publication in the JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY. Manuscript received by the Materials Division June 26, 1998; revised manuscript received December 31, 1999. Associate Technical Editor: Kwai S. Chan.
J. Eng. Mater. Technol. Apr 2000, 122(2): 229-237 (9 pages)
Published Online: December 31, 1999
Article history
Received:
June 26, 1998
Revised:
December 31, 1999
Citation
Park, I. W., and Dornfeld, D. A. (December 31, 1999). "A Study of Burr Formation Processes Using the Finite Element Method: Part II—The Influences of Exit Angle, Rake Angle, and Backup Material on Burr Formation Processes ." ASME. J. Eng. Mater. Technol. April 2000; 122(2): 229–237. https://doi.org/10.1115/1.482792
Download citation file:
Get Email Alerts
An Alternative Finite Element Formulation to Predict Ductile Fracture in Highly Deformable Materials
J. Eng. Mater. Technol (April 2025)
Influence of Ultrasonic Surface Rolling on the Tensile and Fatigue Properties of Laser-Cladding-Repaired 300M Steel Components
J. Eng. Mater. Technol (April 2025)
Blast mitigation using monolithic closed cell aluminium foam
J. Eng. Mater. Technol
Related Articles
A Study of Burr Formation Processes Using the Finite Element Method: Part I
J. Eng. Mater. Technol (April,2000)
Finite Element Modeling of Edge Trimming Fiber Reinforced Plastics
J. Manuf. Sci. Eng (February,2002)
Precision Laser Deburring
J. Manuf. Sci. Eng (November,2001)
3D FEA Modeling of Hard Turning
J. Manuf. Sci. Eng (May,2002)
Related Proceedings Papers
Related Chapters
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
Data Tabulations
Structural Shear Joints: Analyses, Properties and Design for Repeat Loading
Study on Screw Drill Wear When Drilling Low Carbon Stainless Steel and Accompanying Phenomena in the Cutting Zone
International Conference on Instrumentation, Measurement, Circuits and Systems (ICIMCS 2011)