Skip Nav Destination
Issues
December 2018
This article was originally published in
Journal of Micro and Nano-Manufacturing
ISSN 2166-0468
EISSN 2166-0476
In this Issue
Review Article
Opto-Thermophoretic Tweezers and Assembly
J. Micro Nano-Manuf. December 2018, 6(4): 040801.
doi: https://doi.org/10.1115/1.4041615
Topics:
Manufacturing
,
Particulate matter
,
Temperature
,
Temperature gradient
,
Heating
,
Lasers
,
Printing
Electrohydrodynamic Printing for Advanced Micro/Nanomanufacturing: Current Progresses, Opportunities, and Challenges
J. Micro Nano-Manuf. December 2018, 6(4): 040802.
doi: https://doi.org/10.1115/1.4041934
Topics:
Electrohydrodynamics
,
Printing
,
Inks
,
Manufacturing
,
Resolution (Optics)
Research Papers
Low Pressure Phase Transformations During High-Speed, High-Temperature Scratching of Silicon
J. Micro Nano-Manuf. December 2018, 6(4): 041001.
doi: https://doi.org/10.1115/1.4041508
Topics:
Crystals
,
High temperature
,
Phase transitions
,
Pressure
,
Silicon
,
Temperature
,
Diamond turning
,
Diamonds
Model-Based Coarse-Fine Virtual Calibration and Visual Servo for Augmented Reality-Assisted Peg-in-Hole Microassembly
J. Micro Nano-Manuf. December 2018, 6(4): 041002.
doi: https://doi.org/10.1115/1.4041531
Topics:
Calibration
,
Microassembling
,
Servomechanisms
,
Errors
,
Manufacturing
,
Virtual reality
Three-Dimensional Compatible Sacrificial Nanoimprint Lithography for Tuning the Wettability of Thermoplastic Materials
Molla Hasan, Imrhankhan Shajahan, Manesh Gopinadhan, Jittisa Ketkaew, Aaron Anesgart, Chloe Cho, Saransh Chopra, Michael Higgins, Saira Reyes, Jan Schroers, Chinedum O. Osuji, Jonathan P. Singer
J. Micro Nano-Manuf. December 2018, 6(4): 041003.
doi: https://doi.org/10.1115/1.4041532
Topics:
Aluminum
,
Lithography
,
Nanostructures
,
Surface roughness
,
Thermoplastic rubber
,
Wetting
,
Water
,
Elastomers
,
Manufacturing
,
Hydrophobicity
Nanoparticle Sintering Model: Simulation and Calibration Against Experimental Data
J. Micro Nano-Manuf. December 2018, 6(4): 041004.
doi: https://doi.org/10.1115/1.4041668
Topics:
Nanoparticles
,
Simulation
,
Sintering
,
Particulate matter
,
Density
,
Calibration
Technical Brief
Experiment-Based Quantitative Analysis of Picosecond Pulse-Induced Morphological Changes in Fused Silica
J. Micro Nano-Manuf. December 2018, 6(4): 044501.
doi: https://doi.org/10.1115/1.4041509
Topics:
Glass
,
Lasers
,
Ablation (Vaporization technology)
Email alerts
RSS Feeds
Surface Integrity Analysis of Niobium-Based Cermet Processed by Electrochemical Machining and Hybrid Laser-Electrochemical Machining
J. Micro Nano Sci. Eng (September 2025)
An Adaptive Spatial-Terminal Iterative Learning Strategy in Roll-to-Roll Control Problems
J. Micro Nano Sci. Eng (September 2025)
Laser Surface Texturing in Single-Point Incremental Sheet Forming
J. Micro Nano Sci. Eng (September 2025)
Patternable Joule Heat Film With Ultrafast Heating, High-Temperature, and Oxidation-Resistant Surface
J. Micro Nano Sci. Eng (June 2025)
