The demands to increase range, rate of fire, and muzzle velocity have resulted in increased wear and erosion problems in gun tubes. To increase the service life of gun tubes, a number of bore-coating systems are being considered for replacement of the current electroplated high-contractile chromium coating. Two such coating systems are cylindrical magnetron sputtered (CMS) Cr coatings and CMS bilayer coatings. Cylindrical magnetron sputtering is a high-rate vacuum deposition process that has been applied to tubes. Characterization studies of the electroplated and CMS coatings were completed to determine the applicability of these coating/substrate systems for gun bore protection. Each coating system is subjected to a series of tests, including adhesion, microhardness, compositional analysis, and vented erosion-simulation testing (VES). VES testing is completed via a laboratory combustion chamber that reproduces the transient thermal and chemical environments of tank cannon firing on small chord sections of coated gun tubes. In addition to the aforementioned characterization tests, metallography, scanning electron microscopy, and energy dispersive spectroscopy are conducted on each specimen before and after VES testing to evaluate the thermal stability of the coating and the severity of the thermal damage imposed. The mechanisms of damage are investigated, including void formation and micropit growth, oxidation and erosion, and thermomechanical cracking. In addition, methods to further increase resistance to thermal damage are discussed to increase the service life of future gun tube systems.
Skip Nav Destination
e-mail: mulligan@pica.army.mil
Article navigation
Research Papers
Characterization and Comparison of Magnetron Sputtered and Electroplated Gun Bore Coatings
Christopher P. Mulligan,
e-mail: mulligan@pica.army.mil
Christopher P. Mulligan
U.S. Army Armament Research
, Development and Engineering Center, Benét Laboratories, Bldg 115, Watervliet, NY 12189
Search for other works by this author on:
Stephen B. Smith,
Stephen B. Smith
US Army Armament Research
, Development and Engineering Center, Watervliet, NY 12189
Search for other works by this author on:
Gregory N. Vigilante
Gregory N. Vigilante
US Army Armament Research
, Development and Engineering Center, Watervliet, NY 12189
Search for other works by this author on:
Christopher P. Mulligan
U.S. Army Armament Research
, Development and Engineering Center, Benét Laboratories, Bldg 115, Watervliet, NY 12189e-mail: mulligan@pica.army.mil
Stephen B. Smith
US Army Armament Research
, Development and Engineering Center, Watervliet, NY 12189
Gregory N. Vigilante
US Army Armament Research
, Development and Engineering Center, Watervliet, NY 12189J. Pressure Vessel Technol. May 2006, 128(2): 240-245 (6 pages)
Published Online: December 21, 2005
Article history
Received:
December 1, 2005
Revised:
December 21, 2005
Citation
Mulligan, C. P., Smith, S. B., and Vigilante, G. N. (December 21, 2005). "Characterization and Comparison of Magnetron Sputtered and Electroplated Gun Bore Coatings." ASME. J. Pressure Vessel Technol. May 2006; 128(2): 240–245. https://doi.org/10.1115/1.2172963
Download citation file:
Get Email Alerts
The Behavior of Elbow Elements at Pure Bending Applications Compared to Beam and Shell Element Models
J. Pressure Vessel Technol (February 2025)
Related Articles
Role of Platinum in Thermal Barrier Coatings Used in Gas Turbine Blade Applications
J. Eng. Gas Turbines Power (February,2010)
The Microstructural Properties and Tribological Performance of Al 2 O 3 and TiN Nanoparticles Reinforced Ti–6Al–4V Composite Coating Deposited on AISI304 Steel by TIG Cladding
J. Tribol (January,2023)
On the Mechanical Reliability of Photo-BCB-Based Thin Film Dielectric Polymer for Electronic Packaging Applications
J. Electron. Packag (March,2000)
Influence of Titanium in Nickel-Base Superalloys on the Performance of Thermal Barrier Coatings Utilizing γ − γ ′ Platinum Bond Coats
J. Eng. Gas Turbines Power (April,2011)
Related Proceedings Papers
Related Chapters
Surface Analysis and Tools
Tribology of Mechanical Systems: A Guide to Present and Future Technologies
New Descriptor-Based Material Characterization Method Using Micro Compression Test on Spherical Microsamples
Bearing and Transmission Steels Technology
Contact Laws
Contact in Structural Mechanics: A Weighted Residual Approach