The paper addresses the Bauschinger effect under complex stress state in materials with deformation-induced anisotropy whose strain hardening is described by the isotropic–kinematic (translational) type hardening hypothesis. The Bauschinger effect is analyzed using the model based on the yield surface conception and graphical–analytical method of construction of constitutive equations under complex loading. As an example, cylindrical pressure vessels with closed and open ends subjected to autofrettage are considered. The tension–compression Bauschinger effect in the axial and hoop directions as well as the Bauschinger effect under reversed torsion with respect to the longitudinal axis is determined. The role of such factors as the level of prestraining under autofrettage, relation between isotropic and kinematic components of the strain hardening, and chemical composition of the material is analyzed. The results obtained are presented in the form of plots.
Skip Nav Destination
Article navigation
August 2017
Research-Article
Bauschinger Effect Prediction in Thick-Walled Autofrettaged Cylindrical Pressure Vessels
V. Bastun,
V. Bastun
Department of Fracture Mechanics of Materials,
S.P. Timoshenko Institute of Mechanics,
National Academy of Sciences of Ukraine,
Nesterov Street, 3,
Kyiv 03057, Ukraine
e-mail: fract@inmech.kiev.ua
S.P. Timoshenko Institute of Mechanics,
National Academy of Sciences of Ukraine,
Nesterov Street, 3,
Kyiv 03057, Ukraine
e-mail: fract@inmech.kiev.ua
Search for other works by this author on:
I. Podil'chuk
I. Podil'chuk
Department of Fracture Mechanics of Materials,
S.P. Timoshenko Institute of Mechanics,
National Academy of Sciences of Ukraine,
Nesterov Street, 3,
Kyiv 03057, Ukraine
e-mail: ipodil@voliacable.com
S.P. Timoshenko Institute of Mechanics,
National Academy of Sciences of Ukraine,
Nesterov Street, 3,
Kyiv 03057, Ukraine
e-mail: ipodil@voliacable.com
Search for other works by this author on:
V. Bastun
Department of Fracture Mechanics of Materials,
S.P. Timoshenko Institute of Mechanics,
National Academy of Sciences of Ukraine,
Nesterov Street, 3,
Kyiv 03057, Ukraine
e-mail: fract@inmech.kiev.ua
S.P. Timoshenko Institute of Mechanics,
National Academy of Sciences of Ukraine,
Nesterov Street, 3,
Kyiv 03057, Ukraine
e-mail: fract@inmech.kiev.ua
I. Podil'chuk
Department of Fracture Mechanics of Materials,
S.P. Timoshenko Institute of Mechanics,
National Academy of Sciences of Ukraine,
Nesterov Street, 3,
Kyiv 03057, Ukraine
e-mail: ipodil@voliacable.com
S.P. Timoshenko Institute of Mechanics,
National Academy of Sciences of Ukraine,
Nesterov Street, 3,
Kyiv 03057, Ukraine
e-mail: ipodil@voliacable.com
1Corresponding author.
Contributed by the Pressure Vessel and Piping Division of ASME for publication in the JOURNAL OF PRESSURE VESSEL TECHNOLOGY. Manuscript received July 7, 2016; final manuscript received March 31, 2017; published online April 21, 2017. Assoc. Editor: Kunio Hasegawa.
J. Pressure Vessel Technol. Aug 2017, 139(4): 041404 (6 pages)
Published Online: April 21, 2017
Article history
Received:
July 7, 2016
Revised:
March 31, 2017
Citation
Bastun, V., and Podil'chuk, I. (April 21, 2017). "Bauschinger Effect Prediction in Thick-Walled Autofrettaged Cylindrical Pressure Vessels." ASME. J. Pressure Vessel Technol. August 2017; 139(4): 041404. https://doi.org/10.1115/1.4036426
Download citation file:
Get Email Alerts
Cited By
Measurement of Steam-Generator-Tube Vibration Damping Caused by Anti-Vibration-Bar Supports
J. Pressure Vessel Technol (February 2025)
Surface Strain Measurement for Non-Intrusive Internal Pressure Evaluation of a Cannon
J. Pressure Vessel Technol (December 2024)
Dynamic Response and Damage Analysis of a Large Steel Tank Impacted by an Explosive Fragment
J. Pressure Vessel Technol (February 2025)
Related Articles
On the Material Modeling of the Autofrettaged Pressure Vessel Steels
J. Pressure Vessel Technol (October,2009)
Torsion/Simple Shear of Single Crystal Copper
J. Eng. Mater. Technol (July,2002)
In Memoriam: Erastus H. Lee
J. Appl. Mech (July,2007)
Studies on Plastic Flow of Anisotropic Metals
J. Appl. Mech (September,1956)
Related Proceedings Papers
Related Chapters
Basic Concepts
Design & Analysis of ASME Boiler and Pressure Vessel Components in the Creep Range
Analysis of Components: Strain- and Deformation-Controlled Limits
Design & Analysis of ASME Boiler and Pressure Vessel Components in the Creep Range
Analysis of Components Strain and Deformation-Controlled Limits
Analysis of ASME Boiler, Pressure Vessel, and Nuclear Components in the Creep Range