The goal of this work is to investigate the effect of supply pipe position on the heat transfer features of various active clearance control (ACC) geometries, characterized by different jet-to-jet distances. All geometries present 0.8 mm circular impingement holes arranged in a single row. The jets generated by such holes cool a flat target surface, which is replicated by a metal plate in the experimental setup. Measurements are performed using the steady-state technique, obtained by heating up the target plate thanks to an electrically heated Inconel foil applied on the side of the target opposite to the jets. Temperature is also measured on this side by means of an IR camera. Heat transfer is then evaluated thanks to a custom-designed finite difference procedure, capable of solving the inverse conduction problem on the target plate. The effect of pipe positioning is studied in terms of pipe-to-target distance (from 3 to 11 jet diameters) and pipe orientation (i.e., rotation around its axis, from 0 deg to 40 deg with respect to target normal direction), while the investigated jet Reynolds numbers range from 6000 to 10,000. The obtained results reveal that heat transfer is maximized for a given pipe-to-target distance, dependent on both jet-to-jet distance and target surface extension. Pipe rotation also affects the cooling features in a nonmonotonic way, suggesting the existence of different flow regimes related to jet inclination.

The analysis of the interaction between the swirling and liner film-cooling flows is a fundamental task for the design of turbine combustion chambers since it influences different aspects such as emissions and cooling capability. Particularly, high turbulence values, flow instabilities, and tangential velocity components induced by the swirlers deeply affect the behavior of effusion cooling jets, demanding for dedicated time-resolved near-wall analysis. The experimental setup of this work consists of a non-reactive single-sector linear combustor test rig scaled up with respect to engine dimensions; the test section was equipped with an effusion plate with standard inclined cylindrical holes to simulate the liner cooling system. The rig was instrumented with a 2D Time-Resolved Particle Image Velocimetry system, focused on different field of views. The degree of swirl is usually characterized by the swirl number, Sn, defined as the ratio of the tangential momentum to axial momentum flux. To assess the impact of such parameter on the near-wall effusion behavior, a set of three axial swirlers with swirl number equal to Sn = 0.6 − 0.8 − 1.0 were designed and tested in the experimental apparatus. An analysis of the main flow by varying the Sn was first performed in terms of average velocity, RMS, and Tu values, providing kinetic energy spectra and turbulence length scale information. Following, the analysis was focused on the near-wall regions: the effects of Sn on the coolant jets was quantified in terms of vorticity analysis and jet oscillation.

In the recent years Additive Manufacturing (AM) methods are getting more and more attractive and feasible for the realization of components and subcomponents of gas turbines. They are receiving much attention since, on one hand, the manufacturing of complex 3D geometries is allowed and, on the other, manufacturing and delivery times can be cut down. At the current state of the art, to the authors' knowledge only few applications have yet been commercialized relatively to cooling holes, due to the intrinsic difficulties associated with such a critical feature. Lately, Baker Hughes is studying the possibility to manufacture film-cooling holes via the DMLM technology in order to exploit the flexibility of such innovative manufacturing method and hence eliminate additional processes and lead time. From the open literature it is known that additively manufactured holes can have a more irregular shape and higher roughness than traditional ones, which may lead not only to a reduction in coolant flow but more importantly to a decay of the film-cooling adiabatic effectiveness. For this reason, a test campaign has been conducted in collaboration with the University of Florence (Italy) with the objective of characterizing the performance (minimum passage diameter, flow check and adiabatic effectiveness) of AM vs traditional cylindrical holes on simple-geometry coupons built upon different construction angles. Results were then analyzed in order to fully compare the performance of AM vs traditional film-cooling holes at different operating regimes.

Modern gas turbines lean combustors allow to limit NOx pollutant emissions by controlling the flame temperature, while maintaining high turbine inlet temperatures. On the other hand, their adoption presents other challenges, especially concerning the combustor–turbine interaction. Turbine inlet conditions are generally characterized by severe temperature distortions and swirl degree, which, in turn, is responsible for very high turbulence intensities. Several past studies have focused on the description of the effects of these phenomena on the behavior of the high pressure stages of the turbine, both considering them as separated aspects, and, in very recent years, accounting for their combined impact. Nevertheless, very limited experimental results are available when it comes to evaluate the heat transfer coefficient (HTC) on the nozzle guide vane (NGV) external surface, since relevant temperature distortions present a severe challenge for the commonly adopted measurement techniques. The work presented in this paper was carried out on a non-reactive, annular, three-sector test rig, made by a combustor simulator and a NGV cascade. Making use of three real hardware burners of a Baker Hughes heavy-duty gas turbine, operated in similitude conditions, it can reproduce a representative swirling flow, with temperature distortions at the combustor–turbine interface plane. This test apparatus was exploited to develop an experimental approach to retrieve reliable HTC and adiabatic wall temperature distributions simultaneously, in order to overcome the known limitations imposed by temperature gradients on state-of-the-art methods for HTC calculation from transient tests. A non-cooled mockup of a NGV doublet, manufactured using low thermal diffusivity plastic material, was used for the tests, carried out using infra-red thermography with a transient approach. In the authors’ knowledge, this presents the first experimental attempt of measuring a NGV HTC in the presence of relevant temperature distortions and swirl.

The aim of this work is to present the development and application of a measurement technique that allows to record internal heat transfer features of real components. In order to apply this method, based on similar approaches proposed in previous literature works, the component is initially heated up to a steady temperature, then a thermal transient is induced by injecting cool air in the internal cooling system. During this process, the external temperature evolution is recorded by means of an infrared (IR) camera. Experimental data are then exploited to run a numerical procedure, based on a series of transient finite element analyses of the component. In particular, the test duration is divided into an appropriate number of steps and, for each of them, the heat flux on internal surfaces is iteratively updated as to target the measured external temperature distribution. Heat flux and internal temperature data for all the time steps are eventually employed in order to evaluate the convective heat transfer coefficient via linear regression. This technique has been successfully tested on a cooled high-pressure vane of a Baker Hughes heavy-duty gas turbine, which was realized thanks to the development of a dedicated test rig at the University of Florence, Italy. The obtained results provide sufficiently detailed heat transfer distributions in addition to allowing to appreciate the effect of different coolant mass flow rates. The methodology is also capable of identifying defects, which is demonstrated by inducing controlled faults in the component.

Surface roughness is well known to significantly influence turbine aerodynamics and heat transfer; different studies have been undertaken in the last decades, in order to precisely characterize its effects and pursue a reliable and unified computational fluid dynamics modeling approach. Despite the effort, further research is still required to completely fulfill the goal, due to the complexity of the considered environment, with many other aspects and flow characteristics factoring into the final behavior. In this work, an experimental campaign was carried out to evaluate the heat transfer coefficient on a linear nozzle guide vane geometry. The adopted geometry has been developed and tested, at different inlet turbulence intensity, Reynolds and Mach number, at Von Kármán Institute. The results achieved on a test article with smooth surface were made available. In the present work, the effect of increased turbulence level and surface roughness was taken into account, respectively, using passive grids and conditioning the test sample surface finishing. Experiments were conducted using a transient technique by measuring the surface temperature evolution by IR thermography. The collected results integrate the existing database available in the open literature in order to support development and benchmarking of numerical approaches aimed at a reliable characterization of these aspects.

The ever increasing performance requirements of modern aeroengines necessitate the development of effective ways to improve efficiency and reduce losses. Casing temperature control is particularly critical from this point of view, since thermal expansion directly affects the blade tip clearance and thus the associated leakages. To limit the turbine tip flows, active clearance control (ACC) systems have been implemented over the last decades. These systems are usually based upon impingement cooling, generated by a series of perforated manifolds enclosing the turbine casing. When dealing with aeroengine low pressure turbines, the current trend in increasing the engine bypass ratio, so as to enhance the system propulsive efficiency, pushes the limits of ACC traditional design performance. The reduction of the pressure head at the ACC system inlet requires lower nozzle-to-target distances as well as denser impingement arrays to compensate the reduction of the jets' Reynolds number. Literature correlations for the impingement heat transfer coefficient estimation are then out of their confidence range and also RANS numerical approaches appear not suitable for future ACC designs. In this work, methodologies for the development of accurate and reliable tools to determine the heat transfer characteristics of low pressure ACC systems are presented. More precisely, this paper describes a custom designed finite difference procedure capable of solving the inverse conduction problem on the target plate of a test sample. The methodology was successfully applied to an experimental setup for the measurement of the thermal loads on a target plate of a representative low pressure ACC impinging system. The experimental outcomes are then used to validate a suitable numerical approach. Results show that RANS model is not able to mimic the experimental trends, while scale-resolving turbulence models provide a good reconstruction of the experimental evidences, thus allowing to obtain a correct interpretation of flow and thermal phenomena for ACC systems.

Modern lean burn aero-engine combustors make use of relevant swirl degrees for flame stabilization. Moreover, important temperature distortions are generated, in tangential and radial directions, due to discrete fuel injection and liner cooling flows respectively. At the same time, more efficient devices are employed for liner cooling and a less intense mixing with the mainstream occurs. As a result, aggressive swirl fields, high turbulence intensities, and strong hot streaks are achieved at the turbine inlet. In order to understand combustor-turbine flow field interactions, it is mandatory to collect reliable experimental data at representative flow conditions. While the separated effects of temperature, swirl, and turbulence on the first turbine stage have been widely investigated, reduced experimental data is available when it comes to consider all these factors together.In this perspective, an annular three-sector combustor simulator with fully cooled high pressure vanes has been designed and installed at the THT Lab of University of Florence. The test rig is equipped with three axial swirlers, effusion cooled liners, and six film cooled high pressure vanes passages, for a vortex-to-vane count ratio of 1:2. The relative clocking position between swirlers and vanes has been chosen in order to have the leading edge of the central NGV aligned with the central swirler. In order to generate representative conditions, a heated mainstream passes though the axial swirlers of the combustor simulator, while the effusion cooled liners are fed by air at ambient temperature. The resulting flow field exiting from the combustor simulator and approaching the cooled vane can be considered representative of a modern Lean Burn aero engine combustor with swirl angles above ±50 deg, turbulence intensities up to about 28% and maximum-to-minimum temperature ratio of about 1.25. With the final aim of investigating the hot streaks evolution through the cooled high pressure vane, the mean aerothermal field (temperature, pressure, and velocity fields) has been evaluated by means of a five-hole probe equipped with a thermocouple and traversed upstream and downstream of the NGV cascade.

In modern lean-burn aero-engine combustors, highly swirling flow structures are adopted to control the fuel-air mixing and to provide the correct flame stabilization mechanisms. Aggressive swirl fields and high turbulence intensities are hence expected in the combustor-turbine interface. Moreover, to maximize the engine cycle efficiency, an accurate design of the high-pressure nozzle cooling system must be pursued: in a film-cooled nozzle, the air taken from last compressor stages is ejected through discrete holes drilled on vane surfaces to provide a cold layer between hot gases and turbine components. In this context, the interactions between the swirling combustor outflow and the vane film cooling flows play a major role in the definition of a well-performing cooling scheme, demanding for experimental campaigns at representative flow conditions. An annular three-sector combustor simulator with fully cooled high-pressure vanes has been designed and installed at THT Lab of University of Florence. The test rig is equipped with three axial swirlers, effusion-cooled liners, and six film-cooled high-pressure vanes passages, for a vortex-to-vane count ratio of 1:2. The relative clocking position between swirlers and vanes has been chosen in order to have the leading edge of the central airfoil aligned with the central swirler. In this experimental work, adiabatic film effectiveness measurements have been carried out in the central sector vanes, in order to characterize the film-cooling performance under swirling inflow conditions. The pressure-sensitive paint (PSP) technique, based on heat and mass transfer analogy, has been exploited to catch highly detailed 2D distributions. Carbon dioxide has been used as coolant in order to reach a coolant-to-mainstream density ratio of 1.5. Turbulence and five-hole probe measurements at inlet/outlet of the cascade have been carried out as well, in order to highlight the characteristics of the flow field passing through the cascade and to provide precise boundary conditions. Results have shown a relevant effect of the swirling mainflow on the film cooling behavior. Differences have been found between the central airfoil and the adjacent ones, both in terms of leading edge stagnation point position and of pressure and suction side film coverage characteristics.

A novel dry low-NO x gas turbine technology requires well-balanced assessments since the early development phases. The weak knowledge of often conflicting aspects, such as operability and manufacturability, make any roadmap difficult to be drawn. Introduction of innovative manufacturing technologies such as the direct metal laser sintering (DMLS) process allows rapid manufacturing of components and test them in dedicated facilities to support real-time development of new products. The use of such a manufacturing process allows the adoption of designed experiment-based development strategies, which are still uncommon at industrial level, due to the reduced time from drawings to test.The paper describes a reactive test campaign performed by BHGE in cooperation with University of Florence, aimed at the exploration of capabilities of different innovative burners in terms of pollutant emissions containment and blow-out margin. In particular, the test campaign has been conceived to provide a robust estimate of the effects of key geometrical parameters on principal burner performances. The flame stabilization mechanism of the investigated burners is based on the swirling flow generated by different setup of two internal channels: corotating and counter-rotating radial and axial swirlers. The effect of both the shape and the size of the internal air passages, as well as of the swirler characteristics, has been matter of investigation. Burners were tested in a single-cup test rig operated at moderate pressure conditions (up to 6 bar), with two levels of preheated air temperature (300 °C and 400 °C). Each burner was equipped with two natural gas feeding lines representing the diffusion (pilot) and premixed (main) fuel supplies: both lines were regulated during tests to assess the effect of fuel split on emissions and to identify a stable low-NO x operating window, within which a lean blow-out test was performed. Dynamic pressure probes were used to evaluate the onset of combustion instabilities. The burner development was supported by computational fluid dynamics (CFD) investigations with the purpose to have a detailed understating of the flow-field and flame structure and to perform a preliminary screening to select the most promising solutions for the testing phase. The post process of the experimental results has allowed to correlate the main design parameters to burner performance variables discovering possible twofold optimizations in terms of emissions and operability.

International standards regarding polluting emissions from civil aircraft engines are becoming gradually even more stringent. Nowadays, the most prominent way to meet the target of reducing NO x emissions in modern aero-engine combustors is represented by lean-burn technology. Swirl injectors are usually employed to provide the dominant flame stabilization mechanism coupled to high-efficiency fuel atomization solutions. These systems generate very complex flow structures, such as recirculations, vortex breakdown, and processing vortex core, which affect the distribution and therefore the estimation of heat loads on the gas side of the liner as well as the interaction with the cooling system flows. The main purpose of the present work is to provide detailed measurements of heat transfer coefficient (HTC) on the gas side of a scaled combustor liner highlighting the impact of the cooling flows injected through a slot system and an effusion array. Furthermore, for a deeper understanding of the interaction phenomena between gas and cooling flows, a standard two-dimensional (2D) particle image velocimetry (PIV) technique has been employed to characterize the combustor flow field. The experimental arrangement has been developed within EU project LEMCOTEC and consists of a nonreactive three sectors planar rig installed in an open-loop wind tunnel. Three swirlers, replicating the real geometry of a GE Avio partially evaporated and rapid mixing (PERM) injector technology, are used to achieve representative swirled flow conditions in the test section. The effusion geometry is composed by a staggered array of 1236 circular holes with an inclination of 30 deg, while the slot exit has a constant height of 5 mm. The experimental campaign has been carried out using a thermochromic liquid crystals (TLCs) steady-state technique with a thin Inconel heating foil and imposing several cooling flow conditions in terms of slot coolant consumption and effusion pressure drop. A data reduction procedure has been developed to take into account the nonuniform heat generation and the heat loss across the liner plate. Results in terms of 2D maps and averaged distributions of HTC have been supported by flow field measurements with 2D PIV technique focussed on the corner recirculation region.

Over the last ten years, there have been significant technological advances toward the reduction of NO x emissions from civil aircraft engines, strongly aimed at meeting stricter and stricter legislation requirements. Nowadays, the most prominent way to meet the target of reducing NO x emissions in modern combustors is represented by lean burn swirl stabilized technology. The high amount of air admitted through a lean burn injection system is characterized by very complex flow structures such as recirculations, vortex breakdown, and precessing vortex core (PVC) that may deeply interact in the near wall region of the combustor liner. This interaction makes challenging the estimation of film cooling distribution, commonly generated by slot and effusion systems. The main purpose of the present work is the characterization of the flow field and the adiabatic effectiveness due to the interaction of swirling flow, generated by real geometry injectors, and a liner cooling scheme made up of a slot injection and an effusion array. The experimental apparatus has been developed within EU project LEMCOTEC (low emissions core-engine technologies) and consists of a nonreactive three-sectors planar rig; the test model is characterized by a complete cooling system and three swirlers, replicating the geometry of a GE Avio PERM (partially evaporated and rapid mixing) injector technology. Flow field measurements have been performed by means of a standard 2D PIV (particle image velocimetry) technique, while adiabatic effectiveness maps have been obtained using PSP (pressure sensitive paint) technique. PIV results show the effect of coolant injection in the corner vortex region, while the PSP measurements highlight the impact of swirled flow on the liner film protection separating the contribution of slot and effusion flows. Furthermore, an additional analysis, exploiting experimental results in terms of heat transfer coefficient, has been performed to estimate the net heat flux reduction (NHFR) on the cooled test plate.

To deepen the knowledge of the interaction between modern lean burn combustors and high pressure (HP) turbines, a nonreactive real scale annular trisector combustor simulator (CS) has been assembled at University of Florence (UNIFI), with the goal of investigating and characterizing the combustor aerothermal field as well as the hot streak transport toward the HP vanes. To generate hot streaks and simulate lean burn combustor behaviors, the rig is equipped with axial swirlers fed by a main air flow stream that is heated up to 531 K, while liners with effusion cooling holes are fed by air at ambient temperature. Detailed experimental investigations are then performed with the aim of characterizing the turbulence quantities at the exit of the combustion module, and specifically evaluating an integral scale of turbulence. To do so, an automatic traverse system is mounted at the exit of the CS and equipped to perform hot wire anemometry (HWA) measurements. In this paper, two-point correlations are computed from the time signal of the axial velocity giving access to an evaluation of the turbulence timescales at each measurement point. For assessment of the advanced numerical method that is large Eddy simulation (LES), the same methodology is applied to a LES prediction of the CS. Although comparisons seem relevant and easily accessible, both approaches and contexts have fundamental differences: mostly in terms of duration of the signals acquired experimentally and numerically but also with potentially different acquisition frequencies. In the exercise that aims at comparing high-order statistics and diagnostics, the specificity of comparing experimental and numerical results is comprehensively discussed. Attention is given to the importance of the acquisition frequency, intrinsic bias of having a short duration signal and influence of the investigating windows. For an adequate evaluation of the turbulent time scales, it is found that comparing experiments and numerics for high Reynolds number flows inferring small-scale phenomena requires to obey a set of rules, otherwise important errors can be made. If adequately processed, LES and HWA are found to agree well indicating the potential of LES for such problems.