In various plastic forming processes of metals, friction has been revealed to play an important role in the determination of the material flow, fracture, and surface quality. The precise description of friction behavior is thus a critical issue for the accurate prediction and analysis of these formability indicators. Generally, the friction behavior is inevitably affected by material hardening and junction growth. However, few of the previous models have taken both of them into consideration, especially for the nonlinear hardening materials. In this study, the classical contact model was modified to include the power-law hardening material, and the general friction law combined with Tabor's equation was employed to estimate the friction stress with the junction growth of asperities. An asperity-based friction model for rough surfaces in metal forming process was then obtained by summarizing the normal and tangential stresses of all the asperities on the surface using Greenwood and Williamson (GW) method. The model was validated by comparing to the finite element (FE) results and the experimental results. And its comparison with Kogut and Etsion (KE) model and Cohen's model revealed a wider range of application for the present model. It was also found to be able to predict the friction coefficient and the real contact area of nonlinear hardening materials under various contact conditions. This work is helpful to understand the friction behavior and further guide the simulation and optimization of forming processes.
Issue Section:
Other (Seals, Manufacturing)
Reference
1.
Wang
, C.
, Guo
, B.
, Shan
, D.
, and Bai
, X.
, 2012
, “Tribological Behaviors of DLC Film Deposited on Female Die Used in Strip Drawing
,” J. Mater. Process. Technol.
, 213
(3
), pp. 323
–329
.2.
Mróz
, Z.
, and Stupkiewicz
, S.
, 1998
, “Constitutive Model of Adhesive and Ploughing Friction in Metal-Forming Processes
,” Int. J. Mech. Sci.
, 40
(2
), pp. 281
–303
.3.
McFarlane
, J.
, and Tabor
, D.
, 1950
, “Relation Between Friction and Adhesion
,” Proc. R. Soc. London. Ser. A.
, 202
(1069
), pp. 244
–253
.4.
Blau
, P. J.
, 2001
, “The Significance and Use of the Friction Coefficient
,” Tribol. Int.
, 34
(9
), pp. 585
–591
.5.
Bowden
, F. P.
, and Tabor
, D.
, 2001
, The Friction and Lubrication of Solids
, Oxford University Press
, New York
.6.
Leu
, D.-K.
, 2009
, “A Simple Dry Friction Model for Metal Forming Process
,” J. Mater. Process. Technol.
, 209
(5
), pp. 2361
–2368
.7.
Zhao
, Y.
, Maietta
, D. M.
, and Chang
, L.
, 2000
, “An Asperity Microcontact Model Incorporating the Transition From Elastic Deformation to Fully Plastic Flow
,” ASME J. Tribol.
, 122
(1
), pp. 86
–93
.8.
Johnson
, W.
, 1956
, “Extrusion Through Square Dies of Large Reduction
,” J. Mech. Phys. Solids
, 4
(3
), pp. 191
–198
.9.
Wanheim
, T.
, 1973
, “Friction at High Normal Pressures
,” Wear
, 25
(2
), pp. 225
–244
.10.
Greenwood
, J.
, and Williamson
, J.
, 1966
, “Contact of Nominally Flat Surfaces
,” Proc. R. Soc. London. Ser. A.
, 295
(1442
), pp. 300
–319
.11.
Chang
, W.
, Etsion
, I.
, and Bogy
, D. B.
, 1987
, “An Elastic–Plastic Model for the Contact of Rough Surfaces
,” ASME J. Tribol.
, 109
(2
), pp. 257
–263
.12.
Greenwood
, J.
, and Tripp
, J.
, 1970
, “The Contact of Two Nominally Flat Rough Surfaces
,” Proc. Inst. Mech. Eng.
, 185
(1
), pp. 625
–633
.13.
Johnson
, K. L.
, 1987
, Contact Mechanics
, Cambridge University Press
, Cambridge, UK
.14.
Pullen
, J.
, and Williamson
, J.
, 1972
, “On the Plastic Contact of Rough Surfaces
,” Proc. R. Soc. London. A
, 327
(1569
), pp. 159
–173
.15.
Horng
, J. H.
, 1998
, “An Elliptic Elastic–Plastic Asperity Microcontact Model for Rough Surfaces
,” ASME J. Tribol.
, 120
(1
), pp. 82
–88
.16.
Jeng
, Y.-R.
, and Wang
, P.-Y.
, 2003
, “An Elliptical Microcontact Model Considering Elastic, Elastoplastic, and Plastic Deformation
,” ASME J. Tribol.
, 125
(2
), pp. 232
–240
.17.
Kogut
, L.
, and Etsion
, I.
, 2002
, “Elastic–Plastic Contact Analysis of a Sphere and a Rigid Flat
,” ASME J. Appl. Mech.
, 69
(5
), pp. 657
–662
.18.
Jackson
, R. L.
, and Green
, I.
, 2005
, “A Finite Element Study of Elasto-Plastic Hemispherical Contact Against a Rigid Flat
,” ASME J. Tribol.
, 127
(2
), pp. 343
–354
.19.
Kogut
, L.
, and Etsion
, I.
, 2003
, “A Finite Element Based Elastic–Plastic Model for the Contact of Rough Surfaces
,” Tribol. Trans.
, 46
(3
), pp. 383
–390
.20.
Shankar
, S.
, and K.
Arjun
, 2014
, “Effect of Strain Hardening During Unloading for an Elastic-Plastic Hemisphere in Contact With a Rigid Flat
,” Mech. Adv. Mater. Struc.
, 21
(2
), pp. 139
–144
.21.
Kadin
, Y.
, Kligerman
, Y.
, and Etsion
, I.
, 2006
, “Multiple Loading–Unloading of an Elastic–Plastic Spherical Contact
,” Int. J. Solids Struct.
, 43
(22
), pp. 7119
–7127
.22.
Chatterjee
, B.
, and Sahoo
, P.
, 2012
, “Effect of Strain Hardening on Elastic–Plastic Contact of a Deformable Sphere Against a Rigid Flat Under Full Stick Contact Condition
,” Adv. Tribol.
, 2012
(2012
), p. 472794
.23.
Shankar
, S.
, and Mayuram
, M.
, 2008
, “Effect of Strain Hardening in Elastic–Plastic Transition Behavior in a Hemisphere in Contact With a Rigid Flat
,” Int. J. Solids Struct.
, 45
(10
), pp. 3009
–3020
.24.
Spence
, D.
, 1975
, “The Hertz Contact Problem With Finite Friction
,” J. Elasticity
, 5
(3–4
), pp. 297
–319
.25.
Huber
, N.
, and Tsakmakis
, C.
, 1998
, “Experimental and Theoretical Investigation of the Effect of Kinematic Hardening on Spherical Indentation
,” Mech. Mater.
, 27
(4
), pp. 241
–248
.26.
Kucharski
, S.
, and Mróz
, Z.
, 2007
, “Identification of Yield Stress and Plastic Hardening Parameters From a Spherical Indentation Test
,” Int. J. Mech. Sci.
, 49
(11
), pp. 1238
–1250
.27.
Mesarovic
, S. D.
, and Fleck
, N. A.
, “Spherical Indentation of Elastic–Plastic Solids
,” Proceedings of Royal Society London A: Mathematical, Physical and Engineering Sciences
, The Royal Society, pp. 2707
–2728
.28.
Mesarovic
, S. D.
, and Fleck
, N. A.
, 2000
, “Frictionless Indentation of Dissimilar Elastic–Plastic Spheres
,” Int. J. Solids Struct.
, 37
(46
), pp. 7071
–7091
.29.
Orowan
, E.
, 1943
, “The Calculation of Roll Pressure in Hot and Cold Flat Rolling
,” Proc. Inst. Mech. Eng.
, 150
(1
), pp. 140
–167
.30.
Wanheim
, T.
, Bay
, N.
, and Petersen
, A.
, 1974
, “A Theoretically Determined Model for Friction in Metal Working Processes
,” Wear
, 28
(2
), pp. 251
–258
.31.
Tabor
, D.
, 1981
, “Friction—The Present State of Our Understanding
,” J. Lubr. Technol.
, 103
(2
), pp. 169
–179
.32.
Tabor
, D.
, 1959
, “Junction Growth in Metallic Friction: The Role of Combined Stresses and Surface Contamination
,” Proc. R. Soc. London. Ser. A.
, 251
(1266
), pp. 378
–393
.33.
Shaw
, M. C.
, Ber
, A.
, and Mamin
, P. A.
, 1960
, “Friction Characteristics of Sliding Surfaces Undergoing Subsurface Plastic Flow
,” ASME J. Basic Eng.
, 82
(2
), pp. 342
–345
.34.
Tabor
, D.
, 1981
, “Friction—The Present State of Our Understanding
,” ASME J. Tribol.
, 103
(2
), pp. 169
–179
.35.
Mindlin
, R.
, 1949
, “Compliance of Elastic Bodies in Contact
,” ASME J. Appl. Mech.
, 16
, pp. 259
–268
.36.
Kogut
, L.
, and Etsion
, I.
, 2003
, “A Semi-Analytical Solution for the Sliding Inception of a Spherical Contact
,” ASME J. Tribol.
, 125
(3
), pp. 499
–506
.37.
Hamilton
, G.
, 1983
, “Explicit Equations for the Stresses Beneath a Sliding Spherical Contact
,” Proc. Inst. Mech. Eng., Part C
, 197
(1
), pp. 53
–59
.38.
Chang
, W.-R.
, Etsion
, I.
, and Bogy
, D.
, 1988
, “Static Friction Coefficient Model for Metallic Rough Surfaces
,” ASME J. Tribol.
, 110
(1
), pp. 57
–63
.39.
Kogut
, L.
, and Etsion
, I.
, 2004
, “A Static Friction Model for Elastic–Plastic Contacting Rough Surfaces
,” ASME J. Tribol.
, 126
(1
), pp. 34
–40
.40.
Parker
, R.
, and Hatch
, D.
, 1950
, “The Static Coefficient of Friction and the Area of Contact
,” Proc. Phys. Soc. Sec. B
, 63
(3
), p. 185
.41.
Courtney-Pratt
, J.
, and Eisner
, E.
, 1957
, “The Effect of a Tangential Force on the Contact of Metallic Bodies
,” Proc. R. Soc. London. Ser. A.
, 238
(1215
), pp. 529
–550
.42.
Green
, A.
, 1955
, “Friction Between Unlubricated Metals: A Theoretical Analysis of the Junction Model
,” Proc. R. Soc. London. Ser. A.
, 228
(1173
), pp. 191
–204
.43.
Popelar
, C.
, 1969
, “On the Basic Equation of Junction Growth
,” ASME J. Appl. Mech.
, 36
(1
), pp. 132
–133
.44.
Chaudhri
, M. M.
, 1984
, “The Junction Growth Equation and Its Application to Explosive Crystals
,” J. Mater. Sci. Lett.
, 3
(7
), pp. 565
–568
.45.
Nieminen
, J.
, Sutton
, A.
, and Pethica
, J.
, 1992
, “Static Junction Growth During Frictional Sliding of Metals
,” Acta Metall. Mater.
, 40
(10
), pp. 2503
–2509
.46.
Etsion
, I.
, Levinson
, O.
, Halperin
, G.
, and Varenberg
, M.
, 2005
, “Experimental Investigation of the Elastic–Plastic Contact Area and Static Friction of a Sphere on Flat
,” ASME J. Tribol.
, 127
(1
), pp. 47
–50
.47.
Ovcharenko
, A.
, Halperin
, G.
, and Etsion
, I.
, 2008
, “Experimental Study of Adhesive Static Friction in a Spherical Elastic–Plastic Contact
,” ASME J. Tribol.
, 130
(2
), p. 021401
.48.
Ovcharenko
, A.
, Halperin
, G.
, Etsion
, I.
, and Varenberg
, M.
, 2006
, “A Novel Test Rig for In Situ and Real Time Optical Measurement of the Contact Area Evolution During Pre-Sliding of a Spherical Contact
,” Tribol. Lett.
, 23
(1
), pp. 55
–63
.49.
Chang
, L.
, and Zhang
, H.
, 2007
, “A Mathematical Model for Frictional Elastic–Plastic Sphere-On-Flat Contacts at Sliding Incipient
,” ASME J. Appl. Mech.
, 74
(1
), pp. 100
–106
.50.
Brizmer
, V.
, Kligerman
, Y.
, and Etsion
, I.
, 2007
, “A Model for Junction Growth of a Spherical Contact Under Full Stick Condition
,” ASME J. Tribol.
, 129
(4
), pp. 783
–790
.51.
Chang
, W.-R.
, Etsion
, I.
, and Bogy
, D.
, 1988
, “Adhesion Model for Metallic Rough Surfaces
,” ASME J. Tribol.
, 110
(1
), pp. 50
–56
.52.
Derjaguin
, B.
, Muller
, V.
, and Toporov
, Y. P.
, 1975
, “Effect of Contact Deformations on the Adhesion of Particles
,” J. Colloid Interface Sci.
, 53
(2
), pp. 314
–326
.53.
Cohen
, D.
, Kligerman
, Y.
, and Etsion
, I.
, 2008
, “A Model for Contact and Static Friction of Nominally Flat Rough Surfaces Under Full Stick Contact Condition
,” ASME J. Tribol.
, 130
(3
), p. 031401
.54.
Li
, L.
, Etsion
, I.
, and Talke
, F.
, 2010
, “Contact Area and Static Friction of Rough Surfaces With High Plasticity Index
,” ASME J. Tribol.
, 132
(3
), p. 031401
.55.
Ramezani
, M.
, and Ripin
, Z. M.
, 2010
, “A Friction Model for Dry Contacts During Metal-Forming Processes
,” Int. J. Adv. Manuf. Technol.
, 51
(1–4
), pp. 93
–102
.56.
Leu
, D.-K.
, 2011
, “Modeling of Surface Roughness Effect on Dry Contact Friction in Metal Forming
,” Int. J. Adv. Manuf. Technol.
, 57
(5–8
), pp. 575
–584
.57.
Tichy
, J. A.
, and Meyer
, D. M.
, 2000
, “Review of Solid Mechanics in Tribology
,” Int. J. Solids Struct.
, 37
(1
), pp. 391
–400
.58.
Follansbee
, P.
, and Sinclair
, G.
, 1984
, “Quasi-Static Normal Indentation of an Elasto-Plastic Half-Space by a Rigid Sphere—I: Analysis
,” Int. J. Solids Struct.
, 20
(1
), pp. 81
–91
.59.
Sinclair
, G.
, Follansbee
, P.
, and Johnson
, K.
, 1985
, “Quasi-Static Normal Indentation of an Elasto-Plastic Half-Space by a Rigid Sphere—II. Results
,” Int. J. Solids Struct.
, 21
(8
), pp. 865
–888
.60.
Brizmer
, V.
, Kligerman
, Y.
, and Etsion
, I.
, 2007
, “Elastic–Plastic Spherical Contact Under Combined Normal and Tangential Loading in Full Stick
,” Tribol. Lett.
, 25
(1
), pp. 61
–70
.61.
Zhao
, Y.
, and Chang
, L.
, 2001
, “A Model of Asperity Interactions in Elastic–Plastic Contact of Rough Surfaces
,” ASME J. Tribol.
, 123
(4
), pp. 857
–864
.
This content is only available via PDF.
Copyright © 2016 by ASME
You do not currently have access to this content.
