... Contributed by the Tribology Division of ASME for publication in the J ournal of T ribology . 11 06 2024 12 09 2024 12 09 2024 08 11 2024 boundary lubrication electrical wear lubricants third bodies wear mechanisms With the proliferation of electric vehicles (EVs...

... were noticeably diverse due to various factors, such as the combination of wear mechanisms and third-body particles. Wear mechanisms and wear behavior during the tribological investigation will be understood by defining the microstructure of the wear scars, as shown in Figs. 7 and 8 . The deep...

... chemical behavior abrasion adhesion third bodies wear mechanisms As a material that is more resistant to corrosion and stress corrosion cracking, Inconel 690 alloy has become the most popular material used to produce the nuclear steam generator tube (SGT) in pressurized water reactors [ 1...

..., which could explain the fact that, by the end of the test, they had developed a well-established third body layer once again. As for the metal pick-up occurrence, it is speculated that this happening could be related to the oddly higher friction coefficient shown by materials M1-5 and M2-5...

... of ASME for publication in the J ournal of T ribology . 24 08 2021 02 11 2021 02 11 2021 25 11 2021 third particle three-body contact mechanics mixed lubrication load-sharing contact area interface third bodies Ministry of Science and Technology, Taiwan...

... in the J ournal of T ribology . 02 03 2021 16 06 2021 17 06 2021 01 07 2021 fretting wear FEM simulation coated contact pair third bodies Fretting is a phenomenon in which small slip motion occurs on the contact domain and induces wear and fatigue on the material...

... applications under some special working conditions. It is also considered as a wear-resistant material to replace the traditional cobalt-based or iron-based wear-resistant alloys [ 7 – 11 ]. Fe 3 Al alloy sliding wear wear mechanism hardening effect scraper conveyor third bodies 13 07...

... . 26 07 2019 14 04 2020 15 04 2020 18 05 2020 dry friction sliding surfaces third bodies Bulk metallic glasses (BMGs) are a relatively new class of metallic materials developed over the past four decades. Unlike most metallic alloys, which have their atoms arranged...

... sliding surface layers surface properties and characterization surface roughness and asperities surfaces third bodies wear mechanisms The innate credibility of titanium and its alloys is established and explored for maximum utilization of its true potential. The scope and applicability...

.... The composite with single ceramic reinforcement Al 2 O 3 , premixed with metal powder, showed abrasive wear. The composites with single ceramic reinforcement Al 2 O 3 , without premixing, showed delamination and third body wear during wear process. Aluminum alloy AA6061 was used as matrix material...

... fatigue stick-slip third bodies wear Railway transport is generally acknowledged for its low cost, energy efficiency, environmental friendliness, ride comfort, and high speeds (over short and medium distances) compared with other means of transportation. The wear between railway wheels...

... Hydrodynamic lubrication Journal bearings Solid lubricants Third bodies In the hot working environment, the application of conventional oil-lubricated journal bearings is impractical due to the rapid thermal degradation/oxidation of the lubricating oils [ 1 – 4 ]. Under such circumstances, the use...

... received July 22, 2016; final manuscript received January 23, 2017; published online May 26, 2017. Assoc. Editor: Sinan Muftu. 22 07 2016 23 01 2017 Dry friction Films Hardness lubricants Sliding Surfaces Third bodies Wear Magnesium and its alloys have a widespread...

... lower with the increase in Gr content, because the third body of Cu–Al–3%Gr specimen had strong fluidity and plasticity. By contrast, the particle third body of Cu–Al–12%Gr specimen, which contained higher content of Gr, could roll easily. Increased Gr feeding to the third body was reasonable...

..., third body and surface elements impart to the interface many of the characteristics and effects of a hydrodynamic film. Thus, by combining classical Reynolds equation modified for compressible media with the quasi-hydrodynamic/continuum equations and the appropriate rheological and morphological...

...-modification factor for the correct evaluation of the remaining useful life of a dented or abraded contact. Abrasion Indentation Third bodies EHD contacts such as those met in gear teeth and rolling elements of bearings normally operate with lubricating films of submicrometric thickness...