Heat transfer and flow structure are described in a channel with a straight portion followed by a portion with mild curvature at Dean numbers from 100 to 1084. The channel aspect ratio is 40, radius ratio is 0.979, and the ratio of shear layer thickness to channel inner radius is 0.011. The data presented include flow visualizations, and spanwise-averaged Nusselt numbers. Also included are time-averaged turbulence structural data, time-averaged profiles of streamwise velocity, spectra of longitudinal velocity fluctuations, and a survey of the radial time-averaged vorticity component. Different flow events are observed including laminar two-dimensional flow, Dean vortex flow, wavy Dean vortex flow (in both undulating and twisting modes), splitting and merging of Dean vortex pairs, transitional flow with arrays of Dean vortex pairs, and fully turbulent flow with arrays of Dean vortex pairs. Transitional events generally first appear in the curved portion of the channel at Dean numbers less than 350 in the form of arrays of counterrotating Dean vortex pairs. At Dean numbers greater than 350, transitional events occur in the upstream straight portion of the channel but then continue to cause important variations in the downstream curved portion. The resulting Nusselt number variations with curvature, streamwise development, and Dean number are described as they are affected by these different laminar, transitional, and turbulent flow phenomena.
Skip Nav Destination
Article navigation
July 2004
Technical Papers
Experimental Surface Heat Transfer and Flow Structure in a Curved Channel With Laminar, Transitional, and Turbulent Flows
P. M. Ligrani,
P. M. Ligrani
Convective Heat Transfer Laboratory, Department of Mechanical Engineering, MEB 2202, 50 S. Central Campus Drive, University of Utah, Salt Lake City, UT 84112-9208
Search for other works by this author on:
C. R. Hedlund
C. R. Hedlund
Convective Heat Transfer Laboratory, Department of Mechanical Engineering, MEB 2202, 50 S. Central Campus Drive, University of Utah, Salt Lake City, UT 84112-9208
11
Search for other works by this author on:
P. M. Ligrani
Convective Heat Transfer Laboratory, Department of Mechanical Engineering, MEB 2202, 50 S. Central Campus Drive, University of Utah, Salt Lake City, UT 84112-9208
C. R. Hedlund
11
Convective Heat Transfer Laboratory, Department of Mechanical Engineering, MEB 2202, 50 S. Central Campus Drive, University of Utah, Salt Lake City, UT 84112-9208
Contributed by the International Gas Turbine Institute and presented at the International Gas Turbine and Aeroengine Congress and Exhibition, Atlanta, GA, June 16–19, 2003. Manuscript received by the IGTI Dec. 2002; final revision Mar. 2003. Paper No. 2003-GT-38734. Review Chair: H. R. Simmons.
J. Turbomach. Jul 2004, 126(3): 414-423 (10 pages)
Published Online: September 3, 2004
Article history
Received:
December 1, 2002
Revised:
March 1, 2003
Online:
September 3, 2004
Citation
Ligrani , P. M., and Hedlund, C. R. (September 3, 2004). "Experimental Surface Heat Transfer and Flow Structure in a Curved Channel With Laminar, Transitional, and Turbulent Flows ." ASME. J. Turbomach. July 2004; 126(3): 414–423. https://doi.org/10.1115/1.1738119
Download citation file:
Get Email Alerts
Related Articles
Heat Transfer Enhancement by Delta-Wing-Generated Tip Vortices in Flat-Plate and Developing Channel Flows
J. Heat Transfer (December,2002)
Photographs on the Effect of Perforations on the Heat Transfer due to Laminar Flow Over an Extended Surface
J. Heat Transfer (August,2002)
Experimental Investigation of Flow Structure and Nusselt Number in a Low-Speed Linear Blade Passage With and Without Leading-Edge Fillets
J. Heat Transfer (May,2005)
PIV-POD Investigation of the Wake of a Sharp-Edged Flat Bluff Body Immersed in a Shallow Channel Flow
J. Fluids Eng (February,2009)
Related Proceedings Papers
Related Chapters
Cavitating Structures at Inception in Turbulent Shear Flow
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Applications
Introduction to Finite Element, Boundary Element, and Meshless Methods: With Applications to Heat Transfer and Fluid Flow
Extended Surfaces
Thermal Management of Microelectronic Equipment, Second Edition